Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: e-fishin-c

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. I liked the simple victor mousetraps but didn’t...

    I liked the simple victor mousetraps but didn’t like how many snapped traps I found without mouse in it.
    The Tomcat version has been the best so far. Always catches, even up against the wall without...
  2. Replies
    19
    Views
    2,511

    FYI, if you need a clutch disk we matched up a...

    FYI, if you need a clutch disk we matched up a generic one from a 1966-68 vintage Chevrolet car, can’t remember which model. It all matched with the exception of the hub width, a slight alteration...
  3. Replies
    45
    Views
    4,751

    ;)......I see what you did...

    ;)......I see what you did there......:willy_nilly:
  4. Replies
    5
    Views
    791

    Pics of the cyl? Type of lift? ( loading dock...

    Pics of the cyl? Type of lift? ( loading dock lift or man lift )
    You’re gonna need to check the bore for those single acting cylinders, could be rusted.
  5. Replies
    23
    Views
    1,303

    I’ve done plenty of them. Figure out if the leaks...

    I’ve done plenty of them. Figure out if the leaks are in the valve area or the cylinder, both don’t need to come apart. The valve adjustment is touchy so best not to mess with it if it doesn’t leak...
  6. Replies
    23
    Views
    1,303

    Vickers S20/22 Power Steering Units | Hydrostatic...

    Vickers S20/22 Power Steering Units | Hydrostatic Transmission Service
  7. Replies
    23
    Views
    1,303

    That vickers steering cylinder/valve is not hard...

    That vickers steering cylinder/valve is not hard to rebuild. The cylinder separates and can be machined apart at the weld closer to the valve assy. Be careful to save the two square seals between...
  8. Replies
    59
    Views
    7,994

    Agreed, a mill makes it challenging but doable ;)

    Agreed, a mill makes it challenging but doable ;)
  9. Replies
    19
    Views
    2,511

    258278Not sure if any of the old Hydrapower...

    258278Not sure if any of the old Hydrapower components are still avail, but retrofitting a properly sized 4port steering valve, cylinder and matching steering column would probably be more cost...
  10. Replies
    19
    Views
    2,511

    I have that exact Towmotor. We picked it up as a...

    I have that exact Towmotor. We picked it up as a basket case back in the early 90’s for short money cuz the engine and counterweight was off. Still gets used every day.

    Ours has power steering...
  11. Replies
    66
    Views
    5,515

    I bought a Kubota B2320 (23hp) with FEL and BH in...

    I bought a Kubota B2320 (23hp) with FEL and BH in 2010. Fantastic little machine.
    At the time they offered that B series in 23, 26 and 29hp, if I had to do it over the 26 and 29 loader frame and...
  12. Replies
    59
    Views
    7,994

    Overall it’s been a good project, only thing...

    Overall it’s been a good project, only thing missing is a fancy paint job but I’m not a big fan of a rebuild that is mostly paint work.

    At this stage last up will be fitting the new 6-jaw adjust...
  13. Replies
    59
    Views
    7,994

    257149257150 (Dad burn IPhone rotating pics...

    257149257150

    (Dad burn IPhone rotating pics again......:crazy:)
  14. Replies
    59
    Views
    7,994

    Finally putting finishing touches to the Taki....

    Finally putting finishing touches to the Taki. Made a chuck key holder jacket (to keep my labels from getting any worse). Very happy how the custom back splash came out. I use coolant in my work...
  15. Replies
    59
    Views
    7,994

    Not sure why the last pic was turned, my...

    Not sure why the last pic was turned, my photobucket wants me to upgrade ($$)

    Gonna look into some wiring cat track to clean up the scale wires on the back behind the bed. On my larger engine...
  16. Replies
    59
    Views
    7,994

    Finally got a chance this week to play on the...

    Finally got a chance this week to play on the Taki. Finished up the crossfeed reader and saddle reader.

    While it’s not my first DRO it is my first install from scratch. Had to be creative on...
  17. Replies
    23
    Views
    2,989

    Not sure if this will work in your setup but...

    Not sure if this will work in your setup but here’s something I do routinely.

    I have a hyd hose crimper with 8 finger dies (Gates 707) in our shop. When connecting thin wall pipe or tubing I...
  18. Replies
    14
    Views
    1,375

    Dura-bar worked for mine.

    Dura-bar worked for mine.
  19. Replies
    15
    Views
    1,848

    Ditto what ripperj said.......Our box came in...

    Ditto what ripperj said.......Our box came in today too, Great American Textile says Georgia but box says made in Pakistan. Thin but usable.
  20. I have a D1-11, how far away are you?

    I have a D1-11, how far away are you?
  21. Replies
    183
    Views
    27,931

    Wow, just read this thread for the first time. ...

    Wow, just read this thread for the first time. What a nightmare. I have nothing to add but just wanted to say I thank my lucky stars I have seemingly good insurance and a decent workshop space...
  22. Lol.....true. I’m glad to have my wife in the...

    Lol.....true. I’m glad to have my wife in the office as the ole battle ax, it insulates me from all the riff raff
  23. Replies
    22
    Views
    46,060

    Maybe need this YouTube...

    Maybe need this

    YouTube
  24. Replies
    59
    Views
    6,707

    You’re good to go now. Here’s my view on my...

    You’re good to go now.

    Here’s my view on my Asian lathe.

    http://i1116.photobucket.com/albums/k571/e-fishin-c/BB5916FB-1FA7-4C44-BF19-D692B56523EA_zpsb7xetr2f.jpg
  25. HaHa, had to laugh at this cuz one time a former...

    HaHa, had to laugh at this cuz one time a former employee was raking his lawn, neighbor came over to have him fix a mower or snowblower. He said finish raking my leaves and I’ll look at your...
Results 1 to 25 of 222
Page 1 of 9 1 2 3 4