Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: petersen

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    626

    Wet grinding is the method that works on rubber...

    Wet grinding is
    the method that works on rubber rolls.
  2. The rubber seal designed for inserting Sch.40...

    The rubber seal designed for inserting Sch.40 plastic or iron pipe
    into a cast iron "hub" is called a "donut" down at the plumbing supply house.
  3. Once you get it center drilled so you can hold it...

    Once you get it center drilled so you can hold it with tailstock;

    they are not so bad.

    The bigger the four jaw, the better.

    We have done 20 ton hooks with 2-1/2" shank in the 21"...
  4. McMaster-Carr page 1138

    McMaster-Carr page 1138
  5. Replies
    21
    Views
    1,228

    search "dielectric mineral oil"

    search "dielectric mineral oil"
  6. Replies
    7
    Views
    795

    Wet grinding works remarkably well on soft...

    Wet grinding works remarkably well on soft urethanes.

    We do it with simple toolpost grinders.

    I have not used it on Tygon, but it is the first thing I would try.


    ...
  7. Replies
    12
    Views
    1,289

    I do not recall seeing various ways babbit has...

    I do not recall seeing various ways babbit has been used in undercarriage, but I have recast babbit in a number of
    pillow block type bearings for rock crusher feeder aprons.

    In that ugly...
  8. Replies
    11
    Views
    923

    UHMW and HDPE are quite similar to machine;...

    UHMW and HDPE are quite similar to machine; however on thick sections and

    deep machining, the UHMW will warp much much more than HDPE.

    Chose HDPESR (stress relieved) for those...
  9. I have attempted to respond to your private...

    I have attempted to respond to your private message by private message,

    but i am displaying my incompetence in internet skills.
  10. We have had some computer and weather problems...

    We have had some computer and weather problems last night and this morning.

    I think we are ready to send paypal to you now.

    $56.00 right??
  11. We would like to have the Brown and Sharpe...

    We would like to have the Brown and Sharpe Intrimik.

    Will send a private message when I corral computer-competent son next to
    this shiny thing on this desk.

    Petersen
  12. Replies
    12
    Views
    2,262

    Looks like a stock size many places. Most...

    Looks like a stock size many places.

    Most of the aluminum structurals I have bought have come 25' length.

    Ryerson handbook lists 1x2-.125 stock lengths 21'1" (6063-T52)

    Also...
  13. Go right to Hercules in Florida. www...

    Go right to Hercules in Florida.

    www HerculesUS.com 800-796-1300

    Very accomodating...Huge excellent catalogs and listings.
  14. Replies
    30
    Views
    3,147

    Can you find a 3/4" wide cutter that you could...

    Can you find a 3/4" wide cutter that you could stack on an arbor next to

    the 2-3/8" wide cutter you have and grind it to match ??
  15. Replies
    3
    Views
    661

    Hi Bob, I have been looking for more of...

    Hi Bob,

    I have been looking for more of those scales and readers.

    I would like to have both scales both readers.

    I will try to send a private message when I remember how.

    Or I...
  16. We have bought from Brown-Campbell and from...

    We have bought from Brown-Campbell and from McNichols .

    Both have broad product lines and multiple locations.
  17. If you requested a 20' stick of that size, that...

    If you requested a 20' stick of that size, that might be an expensive order to fill;

    since that size is commonly handled in 12' sticks. ( Or maybe your supplier just doesn't like you. )

    My...
  18. Replies
    19
    Views
    1,001

    Are you aware that the correct angle of the "vee...

    Are you aware that the correct angle of the "vee groove" is greater on a larger diameter sheave,

    than on a smaller diameter.

    Getting that right is probably more important than the precise...
  19. If you could live with a 1/4" hex socket, you...

    If you could live with a 1/4" hex socket, you could just whittle them out of
    a 1/2" stripper bolt (shoulder screw).

    Or a 12mm shoulder screw if you prefer a 6mm hex.
  20. Replies
    32
    Views
    2,570

    I too have a 12x30 18 speed that is missing the...

    I too have a 12x30 18 speed that is missing the quick-withdraw lever and internal parts.

    I am interested in those parts if not already spoken for.


    petersen
  21. Replies
    18
    Views
    1,885

    You think 932 and 936 are aluminum bronzes ??? ...

    You think 932 and 936 are aluminum bronzes ???

    You ever heard of 954 ????
  22. Replies
    4
    Views
    700

    M&N Metals, Odessa Texas. 915/332-2535

    M&N Metals, Odessa Texas. 915/332-2535
  23. Replies
    6
    Views
    652

    I agree with Gordon. I found screws for...

    I agree with Gordon.

    I found screws for that purpose on pg. 3055 McMaster-Carr

    listed as 1/4-14 (93880a310)
  24. Replies
    11
    Views
    706

    If it is for a tool, why would you need stainless...

    If it is for a tool, why would you need stainless ??

    Something like 1144 (stressproof) will be stronger and easier to thread.

    That die will cut that thread on 16 mm rod, but 5/8"...
  25. Check out "OREGON". I bought a 40 volt...

    Check out "OREGON".

    I bought a 40 volt OREGON trimmer as an afterthought to get an extra battery
    and charger to go with their 40 volt (self sharpening) CHAIN SAW.

    Both are...
Results 1 to 25 of 153
Page 1 of 7 1 2 3 4