Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JRock1000

Page 1 of 3 1 2 3

Search: Search took 0.04 seconds.

  1. Replies
    22
    Views
    3,676

    There's a good drain plug to Clean and flush the...

    There's a good drain plug to Clean and flush the Knee Cavity.
    Pretty convenient. I've swapped the oil, but I gotta get the gunk out of the bottom of the knee.
    That's easy enough. At this point, I...
  2. For cutting oil?

    For cutting oil?
  3. For cutting oil?

    For cutting oil?
  4. I think he means neat as in unadulterated, same...

    I think he means neat as in unadulterated, same as if you were to order a liquor "neat" - no ice, water or mixer
  5. Replies
    22
    Views
    3,676

    Got the cap off the bottom of the Feed Drive...

    Got the cap off the bottom of the Feed Drive Assembly (third photo is looking up from underneath the knee, at the Feed Drive Assembly)
    264120
    264121
    264122

    Then I got the collar off and the...
  6. Replies
    22
    Views
    3,676

    OK, Been running pretty well with the bracket,...

    OK, Been running pretty well with the bracket, but that's not cutting the mustard anymore.
    I have the Knee off and it turns out the rear bearing on the Back Gear Clutch shaft needs replacing as...
  7. Weird thing, every now and again, I pull a screw...

    Weird thing, every now and again, I pull a screw or hit a pocket of something that smells like some Funky old oil.
    A little kerosene-y but not quite. It's not awful, but it's pungent. Most of the...
  8. Got the soft plug out with a slide hammer. The...

    Got the soft plug out with a slide hammer.
    The knee is off and hanging on an engine hoist.
    I've had it pretty much apart before (on the sides and front) and most of it is in good shape, just these...
  9. Haha, Soft Plug! Tap and Slide Hammer :D Now how...

    Haha, Soft Plug! Tap and Slide Hammer :D
    Now how do I get the feed Drive assembly out, So I can replace the Pinion bearing behind that shaft (wasn't expecting that :( )?
    264079
    264080
  10. Replacing Feed Drive Bearings on VN 22L. How do I remove this plug from back of knee?

    Gotta replace the Bearings from the Feed Drive on Van Norman 22L. How do I remove this plug from the back of the knee?
    Apparently the main shaft with the Cam (the one you see in the photo) needs a...
  11. FS : Miller 320 A/BP Goldstar AC/DC Stick and TIG Welder with footpedal and gauge

    FS : Miller 320 A/BP Goldstar AC/DC Stick and TIG Welder with footpedal and gauge $500
    Near Philadelphia
    257116257117257118257119
    I just don't have the room for it.
  12. That's Great! Thanks!

    That's Great! Thanks!
  13. The Drawbar spins loose in the spindle, then,...

    The Drawbar spins loose in the spindle, then, although the face key does drive it, it has play in the Y axis. Not safe.


    No key in the stub arbor.

    Why would they even make a left handed...
  14. What's the OD on the spacers, on your 1 1/4"...

    What's the OD on the spacers, on your 1 1/4" arbor?
    Got a stub arbor with the machine. 1" arbor, 1 3/8" spacers.
    Got a major flaw though. Left Handed thread on the arbor nut.
    I could just run it...
  15. Thanks! Good to know. I was leaning towards 1...

    Thanks!
    Good to know.
    I was leaning towards 1 3/4" (cause I have a bar of 01 round Stock that size).
    I've got a bunch of cutters already, and most of them are 1 1/4" arbor hole.
  16. Standard size Arbor "Running Bushing" for Horizontal Milling Machine?

    Is there a standard size Running Bushing for Horizontal Milling Machines?
    I'm building an overarm support for a VN22L.
    Most of my cutters are for 1 1/4" arbors and a few are 1" (or smaller)....
  17. Had good experiences selling (and buying) on FB...

    Had good experiences selling (and buying) on FB marketplace.
    It's pretty easy. Shipped a few items. They just paid via Paypal.
    Even sold a Nichols Milling Machine and a Versa-Mil.
    Bought PLenty of...
  18. Glad it made it safe and sound. Tried to walk...

    Glad it made it safe and sound.
    Tried to walk the line between making it easy for you, and difficult for the forklift, to open.
    Looks like they took a chunk off the corner of that pallet :D
    I'm a...
  19. Replies
    23
    Views
    2,404

    To make a single drive ear. This stock wasn't...

    To make a single drive ear.
    This stock wasn't thick enough to make both drive ears, and I hadn't figured out an elegant way to weld them on.
    I needed enough meat on the tab to attach the Drive key...
  20. Replies
    22
    Views
    3,676

    Got in there and looked at it tonight. The shear...

    Got in there and looked at it tonight. The shear pin has that little wire wrapped around it?
    That all seems to be in good shape.
    I wish it were that easy.
    It's the back bearing on the Bevel Gear...
  21. Replies
    22
    Views
    3,676

    SO how did you align the shafts / shear pin...

    SO how did you align the shafts / shear pin holes, after the pin sheared and the shafts rotated out of alignment with each other?
    Just stick a rag in the gears (to lock them) and twist the other...
  22. Sure does. They're gonna need the forklift to get...

    Sure does. They're gonna need the forklift to get it off my truck
  23. Replies
    22
    Views
    3,676

    Got it, I think it's just sticky around the 5s on...

    Got it, I think it's just sticky around the 5s on the feed settings.
    Just gotta run it halfway between feeds till everything starts moving again.
    Hopefully that'll loosen up as I use it more...
  24. Replies
    22
    Views
    3,676

    Made this cut on a forklift fork ...

    Made this cut on a forklift fork

    https://youtu.be/sEEyG8Ljueg

    Then while I was setting up to bevel the edges for welding, it jammed!
    It made a weird (er than usual) noise in the rapids, then...
  25. Replies
    22
    Views
    3,676

    Here's her first good meal :) Powerfeeds working...

    Here's her first good meal :)
    Powerfeeds working well, and B&S #13 - 40 taper adapter in place.

    https://youtu.be/N6kY16U15Rs
Results 1 to 25 of 74
Page 1 of 3 1 2 3