Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Richard King

Page 1 of 60 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    58
    Views
    1,892

    Here are some pictures of what I...

    Here are some pictures of what I said.305357305358305359305360305361
  2. Replies
    58
    Views
    1,892

    Buck, you can zero the indicator on the tailstock...

    Buck, you can zero the indicator on the tailstock side and if you have one on the top too. then losen the TS and move it down a foot down the bed and lock it and then move the saddle down to that...
  3. Replies
    58
    Views
    1,892

    Turn down an aluminum or leaded cold roll shaft...

    Turn down an aluminum or leaded cold roll shaft say sticking out the chuck 6" the same diameter as the tailstock test bar and butt the tailstock bar to the Head stock test bar and measure the side...
  4. Replies
    87
    Views
    6,189

    You should have called me this morning. You have...

    You should have called me this morning. You have or had my number and email ... It started at 10 AM CST. It was a Bidspotter. under fram fram...Minneapolis. I don't watch the forrum 24/7 so you...
  5. Replies
    87
    Views
    6,189

    Yes there is a auction up here tomorrow ending at...

    Yes there is a auction up here tomorrow ending at 10 CST. . ai
  6. We set a date - Feb 10 to 14, 2021. ...

    We set a date - Feb 10 to 14, 2021. Fayetteville is about 1 1/2 hour south of Nashville. I just put a ad on Ebay selling the class. The shop owner said he has several surface plates, several work...
  7. Replies
    6
    Views
    532

    Being it is an Asian lathe and on most Asian...

    Being it is an Asian lathe and on most Asian lathes the head-stock is setting on a flat surface and can rotate on a pin under it so it can be aligned with the bed. If I were scraping it I would...
  8. More Pic's:

    More Pic's:
  9. We did the class and it finished on Sunday. Here...

    We did the class and it finished on Sunday. Here are some pictures.

    304995304996304997304998
  10. Replies
    4
    Views
    576

    Storebro lathes...

    Storebro lathes

    UK Lathes sells manuals. Possibly a PDF
  11. If I were you I would call Dave Beiring at Tri...

    If I were you I would call Dave Beiring at Tri Star plastics. Tstar.com. he has been selling bearing material to Captain Scientific for dozens of years. Capt. Is the supply house that sells to...
  12. What's happening with yours?

    What's happening with yours?
  13. Replies
    16
    Views
    803

    Have you checked oout Standard and Modern? They...

    Have you checked oout Standard and Modern? They are made or were made in Canada. I believe they maybe made in India now, but the home office is in Canada. Check them out and let us know...please....
  14. PROTOTRAK Mill rebuild class in Feb or March, 2021 - Fayetteville TN

    Hello all I had a good size shop owner call me today and he has a Prototrak VMC apart and wants to replace the X and Y Turcite. I said I could possibly do it in February or March. He said he has a...
  15. I had a student at a GM plant in Indianapolis who...

    I had a student at a GM plant in Indianapolis who challenged me to a race. We started with 2 of my 3/4 x 3" x 12" cast iron bars milled to .001" accuracy. He hand scraped and I power scraped. He...
  16. Do it and be sure to tell us all about it and how...

    Do it and be sure to tell us all about it and how successful it was. A lot of pictures. It should be interesting and I also have the same opinion as Phil.
  17. Replies
    2
    Views
    456

    I saw this in Vintagemachine.org on page 35 it...

    I saw this in Vintagemachine.org on page 35 it shows a milling cutter cutting the round. I can check with Bourn & Koch as hey ended up with the Ingersoll library I believe.
    ...
  18. Replies
    23
    Views
    1,150

    If you decide to dismantle the knee, rotate the...

    If you decide to dismantle the knee, rotate the feed handle to the lowest feed. If you can run it that is. The timing marks on the gears are aligned that way. That is a beauty as it was designed to...
  19. Bruce check with Franz and Stefan as they bought...

    Bruce check with Franz and Stefan as they bought several used scrapers from Biax that were parts machines.
  20. My 24" is called a HKA-24 and it was designed to...

    My 24" is called a HKA-24 and it was designed to scrape the top of the knee of a Bridgeport knee type mill. I sell castings, but can get the ground and if you want it scraped, I can teach you how or...
  21. Email these guys and ask them, say, I am the guy...

    Email these guys and ask them, say, I am the guy who taught them to scrape and I was hoping they could help you, maybe able to help or know someone who can: Services | CAMPAT Machine Tool
  22. I have a few...just need to figure out a $$

    I have a few...just need to figure out a $$
  23. Replies
    15
    Views
    907

    I found this parts manual on an 1926 machine. ...

    I found this parts manual on an 1926 machine. Page 12 shows the tail stock...http://vintagemachinery.org/pubs/2185/24279.pdf does this look like yours?

    A machine almost 100 years old ?? It...
  24. November 11 - 15 Los Angeles Scraping Class Moved

    We had issue with the Burbank location and had to move the class to Montebello about 45 minute drive SE of Burbank. The new shop is bigger and those who wanted to bring there Bridgeport can now. ...
  25. Replies
    23
    Views
    1,150

    I have the best results using super HOT water and...

    I have the best results using super HOT water and industrial soap. Use a long handle bristle brush and scrub hard. Go buy some cotton rags at Ragstock and then on the rough spots. Use a hand...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4