Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Rob F.

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. cleared some space

    cleared some space
  2. PM sent re shipping.

    PM sent re shipping.
  3. I need to check my clamp set to be sure but I can...

    I need to check my clamp set to be sure but I can probably use this. I will go to the shop this eve and check.
  4. Replies
    114
    Views
    7,423

    Please explain how USA overthrowing Libya (or any...

    Please explain how USA overthrowing Libya (or any other small country) expanded freedom here at home.
  5. Replies
    114
    Views
    7,423

    I dont understand what you mean.

    I dont understand what you mean.
  6. Replies
    114
    Views
    7,423

    This thread seem to bring patriotism into...

    This thread seem to bring patriotism into question so I will ask "Is it patriotic to criticize our gov?" Or is it "more patriotic" to do what the gov wants at all times?
    Here are some links I found...
  7. Replies
    114
    Views
    7,423

    Please answer EG's question about how exactly...

    Please answer EG's question about how exactly beating up on small overseas countries "protects our freedom" here in mainland USA.

    Like what happened in Libya? Protecting our freedom?

    Ten...
  8. Replies
    11
    Views
    528

    If stick works, then check pedal etc. Pedal gets...

    If stick works, then check pedal etc. Pedal gets plenty of abuse being kicked around on the ground. If stick does not work then look more at machine itself.
    Can you do tig mode with panel control on...
  9. YouTube...

    YouTube
    https://www.youtube.com/watch?v=Dp0Bt2cbcc8

    Trying to discuss facts with gus the goat
  10. Replies
    11
    Views
    528

    Does it still work on stick mode? If so foot...

    Does it still work on stick mode?
    If so foot pedal is most likely suspect, look for dirt in pedal, bad cord or connection to machine is dirty or corroded as a starting point.
  11. Did you just admit to being a fake? ;)

    Did you just admit to being a fake? ;)
  12. Looking at the sellers other items there are...

    Looking at the sellers other items there are quite a lot of machines.
    Filter your search on his items by "most expensive first", to not get cluttered with the little stuff he also has.
  13. Use brass or plastic tipped screws to hold work...

    Use brass or plastic tipped screws to hold work in cathead if you can not mar the workpiece.
  14. Replies
    8
    Views
    560

    Pics of the rest of your new machine?

    Pics of the rest of your new machine?
  15. Replies
    7
    Views
    717

    One of the guys said it is the biggest truck and...

    One of the guys said it is the biggest truck and trailer in north america, pretty impressive.
  16. Replies
    8
    Views
    733

    I was also thinking about this, I'm not sure but...

    I was also thinking about this, I'm not sure but I would think air is slower than oil.
  17. Replies
    9
    Views
    958

    Here is an old thread on the short cut lathe:...

    Here is an old thread on the short cut lathe:
    Seneca Falls Short Cut Gear head Lathe
  18. This article seems to think there is a bit more...

    This article seems to think there is a bit more to the mass shootings than meets the eye.
    I did not read the entire thing yet since it is a bit long but the last section discusses the shootings a...
  19. Replies
    8
    Views
    733

    Oil quenches slower than water. Water quenching...

    Oil quenches slower than water. Water quenching oil hardening rod may cause it to crack. Oil quenching water hardening rod may not get to full hardness.
  20. Replies
    7
    Views
    379

    The propane regulator/vaporizer could be gunked...

    The propane regulator/vaporizer could be gunked up with tar. They usually have a plug that can be removed to clean it out. Do it with the engine hot so the tar is soft.
    These devices use radiator...
  21. Replies
    61
    Views
    4,904

    Why is my comment stupid? If it is as YOU say:...

    Why is my comment stupid? If it is as YOU say: :"The part I want made is very, very common part that was produced in the millions over a 25 year span. I'll bet there are ten sitting within a 5 mile...
  22. Replies
    35
    Views
    3,176

    bigger pic of the ladder set up in this thread,...

    bigger pic of the ladder set up in this thread, post #109:

    My gantry crane build
  23. Now you have a part # see if your local welding...

    Now you have a part # see if your local welding store can get it for you, they should be ordering regularly from them.
  24. Replies
    111
    Views
    16,231

    The engine was probably added to the beam on the...

    The engine was probably added to the beam on the ladders, look at where there should be a hook on the hoist to hang the engine from.
  25. Replies
    61
    Views
    4,904

    These guys ought to have it if it is such a...

    These guys ought to have it if it is such a common part:
    Used Auto Parts Houston | Salvage yards | LKQ Pick Your Part
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4