Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: johnoder

Page 1 of 60 1 2 3 4

Search: Search took 0.15 seconds.

  1. Replies
    8
    Views
    157

    Here is the 36 at play on a 14" AL disc - gets...

    Here is the 36 at play on a 14" AL disc - gets flat while you play elsewhere

    319084319085

    Crank I made for it since it had none

    319086319087319088
  2. Replies
    8
    Views
    157

    And the other thread ...

    And the other thread

    https://www.practicalmachinist.com/vb/antique-machinery-and-history/ohio-shaper-questions-390010/#post3743975

    with info
  3. Replies
    1
    Views
    90

    A funny question for folks that have yet to hear...

    A funny question for folks that have yet to hear about a size :confused:

    Measure length of table where vise is bolted down - my 36" plain is 36" there - and not being a Dreadnought, weighs but...
  4. Replies
    5
    Views
    1,150

    Just turned down a 35/64 MT2 to .547 dia. (to...

    Just turned down a 35/64 MT2 to .547 dia. (to suit a holder someone made ex Reed Roller Bit). Plainly plain old steel back there - HSS ate it up
  5. And heaps and heaps of magnetos, starters and...

    And heaps and heaps of magnetos, starters and generators for the round engines of all sizes
  6. Replies
    6
    Views
    218

    Only if you run it too fast. When new, I doubt...

    Only if you run it too fast. When new, I doubt the spindle went much past 350. That was the way of the world then.

    The photos show the vee belt drive does in fact run the spindle way too fast -...
  7. Replies
    28
    Views
    1,089

    There you go

    There you go
  8. Replies
    9
    Views
    398

    Nope - as long as it has the "star" knob for...

    Nope - as long as it has the "star" knob for shifting feeds on face of apron it is a Series O - which means it is not a "model A" as they came along later - even though it has the QC gearbox - and...
  9. Replies
    28
    Views
    1,089

    Can you share info for that source?

    Can you share info for that source?
  10. Here is the forum owner's input on such, Indy ...

    Here is the forum owner's input on such, Indy

    Machinery Discussion Guidelines
  11. Replies
    9
    Views
    488

    All answered in here likely - plus gobs of how to...

    All answered in here likely - plus gobs of how to

    http://vintagemachinery.org/pubs/1617/5795.pdf

    Have fun
  12. Bought a new ACME three phase dry type general...

    Bought a new ACME three phase dry type general purpose 3 KVA to run 1.5 HP four speed in 2001 - works perfectly "backwards" - a lash up approved by ACME. Never any issues of any kind in those twenty...
  13. Email sent on the resell plan

    Email sent on the resell plan
  14. I'd guess Sebastian from the QC gear box - before...

    I'd guess Sebastian from the QC gear box - before their many little gear heads
  15. The most info crammed edition of all of them -...

    The most info crammed edition of all of them - even though a bit older than 1937.

    http://vintagemachinery.org/pubs/1617/5795.pdf

    Have Fun
  16. Replies
    2
    Views
    230

    Yours looks better than mine - I'll take it. PM...

    Yours looks better than mine - I'll take it. PM sent
  17. "Geared" apron - easily recognized with its...

    "Geared" apron - easily recognized with its clutch knob in bottom center - and the lead screw from 9B or 9A with the right length

    You might first FIND OUT from folks like SB man (Ted) if such...
  18. My all time favorite Federal is this good size (...

    My all time favorite Federal is this good size ( 3" OD ? ) example that has .400" travel and is a "tenth" indicator

    For actual photos instead of Photo Bucket silliness, see Post #10
    ...
  19. Replies
    17
    Views
    3,933

    Provavelmente não será informação - a menos que...

    Provavelmente não será informação - a menos que alguém tenha um catálogo antigo o suficiente em Le Blond O
  20. I have one ancient L.S.S. left over from the...

    I have one ancient L.S.S. left over from the sixties apprenticeship. Every thing else is Federal - and not one of them came up short on me in close to fifty years of having them and using them
  21. Replies
    530
    Views
    98,502

    Getting on up there - A.I.S.C. Steel...

    Getting on up there - A.I.S.C. Steel Construction shows near 150 total allowable moment in kip ft in a 16 foot unbraced span for 14 X 53 in the beam tables page 2- 72. This is for the 50K steel...
  22. Replies
    530
    Views
    98,502

    Looks good Matt - maybe even tall enough to help...

    Looks good Matt - maybe even tall enough to help with the 10 foot tall 15,000 Lb Jig Bore - though the weight may be a bit much. What size/weight is that top wide flange?
  23. Replies
    11
    Views
    455

    Ever email? You can attach a photo to an email...

    Ever email?

    You can attach a photo to an email sent from your phone to your "confuser"

    My phone has an "orange blob" lower right you punch for starting an email - and punching it will show you...
  24. Replies
    45
    Views
    2,299

    Less likelihood of busting them off during a move...

    Less likelihood of busting them off during a move (like on my 16 X 102 Monarch)
  25. Replies
    11
    Views
    455

    From elsewhere if of interest Posting...

    From elsewhere if of interest


    Posting Pictures on the South Bend Forum
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4