Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Glug

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. That all could have been avoided if you had...

    That all could have been avoided if you had ordered some NOS kitty litter from Monarch.
  2. Replies
    12
    Views
    1,037

    Bucksted!!

    Bucksted!!
  3. Thread: Carla

    by Glug
    Replies
    17
    Views
    2,606

    Sad. When I saw Carla post on a topic, I knew I...

    Sad. When I saw Carla post on a topic, I knew I was going to learn something good.

    I recall her writing about having a substantial archive of manufacturing and history from Columbia vise co. It...
  4. Replies
    162
    Views
    16,003

    Thinking the pant cuffs are a bigger worry than...

    Thinking the pant cuffs are a bigger worry than the sleeves. He should probably wear those skinny jeans when riding the cut.

    ...
  5. Replies
    162
    Views
    16,003

    Hang this photo next to the "no chairs" rule. ...

    Hang this photo next to the "no chairs" rule.


    https://i.pinimg.com/originals/f1/be/e5/f1bee566f74f09611dd144cc18a6dbf6.jpg
  6. So, after more than three years, did you ever...

    So, after more than three years, did you ever find that ultra precision bearing?
  7. Replies
    26
    Views
    2,530

    His feedback is limited and the sales are all on...

    His feedback is limited and the sales are all on small items. Given the extremely sparse description - "Monarch lathe. Condition is used" - that may be wishful thinking.

    The OP is only 30 minutes...
  8. Replies
    4
    Views
    595

    Any lathe with a goofy name and no place of...

    Any lathe with a goofy name and no place of origin is likely Chinesium home shop special and not allowed here, per the Machinery Discussion Guidelines Sticky, posted at the start of this forum,...
  9. Replies
    48
    Views
    3,681

    Stop bragging.

    Stop bragging.
  10. Replies
    14
    Views
    1,352

    CRC 3-36 is great stuff and is surprisingly good...

    CRC 3-36 is great stuff and is surprisingly good at preventing rust. I was skeptical but after it dries it leaves an extremely thin protective layer that even works on vise anvils in active northern...
  11. Replies
    30
    Views
    2,165

    "Practical Seamstress"

    "Practical Seamstress"
  12. Replies
    9
    Views
    1,599

    So the snowmobile you are attaching to the 10ee -...

    So the snowmobile you are attaching to the 10ee - you'll have it on blocks? Will you be disconnecting it to ride it in the winter? I wonder if the gas motor will cause excessive vibration? I suppose...
  13. Replies
    1
    Views
    481

    Image hosting site Use.com is closing soon

    The excellent free image hosting site use.com is closing down. It's sad - I've used them for many years and mentioned them here several times. They allowed unlimited image sizes and videos, all...
  14. Replies
    928
    Views
    36,414

    Well, if the USA is not going to buy Greenland, I...

    Well, if the USA is not going to buy Greenland, I am.

    I just need to find a few oligarchs to co-sign my loan.
  15. Replies
    928
    Views
    36,414

    "Charlie don't surf!"

    "Charlie don't surf!"
  16. U.S. Steel idles blast furnaces, cites lower demand and prices

    They say demand and prices are down. Hot rolled is mentioned. Are you seeing lower steel prices? Looks like the layoffs have increased since the June announcement.



    U.S. Steel plans to lay off...
  17. Replies
    47
    Views
    2,873

    Guess the neighbors should have helped him out...

    Guess the neighbors should have helped him out sooner, eh?
  18. Thread: OSHA results

    by Glug
    Replies
    76
    Views
    10,297

    In the 80's we had an office situation where we...

    In the 80's we had an office situation where we needed to extend power to 25 or so computer workstations. The inspector said extension cords were not acceptable and we would need to have an...
  19. Replies
    12
    Views
    1,408

    My made in 1969 1408 AVS apparently has the same...

    My made in 1969 1408 AVS apparently has the same 7.5HP motor. The 120V @ 56.25 amp armature seems a bit odd. Field is 240V. Monarch would not send me anything about the drive, they would just say...
  20. After all that you have said about limited land...

    After all that you have said about limited land and crowding and expense, how is it that Ribeye is $10/lbs in the US, at large discount member clubs like Costco when bought in bulk packs for about...
  21. Replies
    64
    Views
    4,525

    The thing I can't figure is Zoro is pretty good,...

    The thing I can't figure is Zoro is pretty good, prices are excellent. Grainger is their parent company and the selection seems pretty close.

    Though the Zoro website was "redesigned" 7 months ago...
  22. Replies
    61
    Views
    6,028

    So this thread isn't about Trump lathes? ...

    So this thread isn't about Trump lathes?


    http://industrialmachinery.com/store/images/11889.jpg
  23. Replies
    86
    Views
    5,464

    For production cars, Ferrari has long prioritized...

    For production cars, Ferrari has long prioritized looks over the performance and reliability at the track. Their brake systems are often poorly engineered and inadequate. Whta kind of track car is...
  24. IIRC, there is a video (or was it just photos?)...

    IIRC, there is a video (or was it just photos?) that touts the superiority of the L taper and even shows parts being cut directly on the spindle - no chuck.



    This comes up every so often but...
  25. Help fetching a 10ee from Tallahassee to Tampa

    A friend won a nice round dial at auction in Tallahassee. I know he'll be over here soon enough. If anyone has the time or inclination, he could really use a hand at either end of the journey, even...
Results 1 to 25 of 451
Page 1 of 19 1 2 3 4