Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Panza

Page 1 of 38 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    24
    Views
    2,397

    My NLX came from Japan, but I heard they make...

    My NLX came from Japan, but I heard they make them in Italy too. But I don't know that.
  2. Replies
    24
    Views
    2,397

    I have had issues with the Service from DMG Mori...

    I have had issues with the Service from DMG Mori Sweden from day one. Hence no updates.
    They don't even keep written agreements.
    Very disappointed with the whole deal.
    Machine is ok but with the...
  3. Thread: Smart key levels

    by Panza
    Replies
    13
    Views
    3,456

    Ended up getting nothing. :mad5:

    Ended up getting nothing. :mad5:
  4. Replies
    2
    Views
    322

    I am sorry I can't explain any more. It was only...

    I am sorry I can't explain any more. It was only briefly mentioned when I got my lathe. I will ask further this week when I am going to have the last training with DMG. Although I am sure I will be...
  5. Replies
    2
    Views
    322

    Anyone got Celos ver.B29 ?

    I was informed by DMG Mori (when I asked) that there is a new version of Celos: B29.

    Earlier this year they said the next version will improve tool offsets so it is easier to run double lathe...
  6. That Mori is a beast. Some guy at DMG Mori told...

    That Mori is a beast. Some guy at DMG Mori told me that the current NLX is just a year-by-year improvement of the lathe you have. To me the basics looks exactly the same on the machines. I inquired...
  7. Replies
    61
    Views
    8,396

    I don't agree that the whole control is useless....

    I don't agree that the whole control is useless. I don't use all the work-planning stuff so can't comment on that but I find the conversational programming quite good. The milling side could have...
  8. Replies
    9
    Views
    1,082

    It is not anchored down. I offered them to anchor...

    It is not anchored down. I offered them to anchor it but they said it was not needed. The adjusting feet does not have locknuts either.

    Thanks for the tip of turning down the middle of the testbar...
  9. Replies
    9
    Views
    1,082

    The cut was a light cut (0,1mm DOC or so) in 3,5"...

    The cut was a light cut (0,1mm DOC or so) in 3,5" Stressproof. Held in the chuck, since the sub was tested separately.
    The taper I mentioned was total taper.
    The tech came from the manufacturer. He...
  10. Replies
    9
    Views
    1,082

    Taper tolerances on new CNC Lathes ?

    I am having a little discussion with the company that sold me my newest CNC lathe ( 8" chuck , 500mm turning length) regarding the taper the machine turns.
    After it was installed and leveled (by...
  11. IMO you are right in trying to use cam for more...

    IMO you are right in trying to use cam for more than simple milling. The smart control in limited in the conversational milling and it is not always easy to debug your milling programs.
  12. Thread: Smart key levels

    by Panza
    Replies
    13
    Views
    3,456

    After much trouble it seems I can buy the key...

    After much trouble it seems I can buy the key with the right access. I'll try to get it included.
    Also trying to get the machine door interlock fixed.
  13. Thread: Smart key levels

    by Panza
    Replies
    13
    Views
    3,456

    We will see if I get what I want. Still nothing...

    We will see if I get what I want.
    Still nothing new from DMG: More than 3 months from the machine was delivered and ready for install a lot of things are still missing.
  14. Thread: New Machine day

    by Panza
    Replies
    15
    Views
    2,182

    How's this coming along ? I am sure more than me...

    How's this coming along ? I am sure more than me wants to see more of that machine.
  15. Replies
    192
    Views
    27,540

    I ran Syntilo 2000 in my QT lathe and had it at...

    I ran Syntilo 2000 in my QT lathe and had it at 5%. No rust problems at all. But it did form some sort of oil-sludge.
  16. Replies
    18
    Views
    1,866

    The leadscrew reverse handle is there. From what...

    The leadscrew reverse handle is there.
    From what I can see someone put the clutch rod in the wrong orientation and just bent the clutch lever(s) to suit..
  17. Does anyone have the software to print Maztrol programs ?

    I have a few 10s of Mazatrol programs from the QT lathe that I sold. Now I would like to look at some of the programs for reference when I program my new lathe.
    Anyone have the software to...
  18. Thread: McRee Shop #1

    by Panza
    Replies
    19
    Views
    4,213

    So, the machine is out of whack one or more ways...

    So, the machine is out of whack one or more ways by 5 thouh instead of 5 tenths ? I assume you have enough turcite or similar to scrape on to get it back in alignment ? Which axes are out and how...
  19. Replies
    217
    Views
    64,053

    Isn't it possible to adapt an X-axis cover from a...

    Isn't it possible to adapt an X-axis cover from a newer machine ?
    Like this type: $341.70 - MAZAK QS20N-4 AXIS-U CNC LATHE 33" X 18"...
  20. Replies
    10
    Views
    1,302

    Have you talked to JB at Ravema head office...

    Have you talked to JB at Ravema head office directly ? If not, you should.
    Have you paid for the machine in full ? If not: You know what to do.
    If none of those works: Write an email to the Ravema...
  21. If you can't make it stand still in any other...

    If you can't make it stand still in any other way: Maybe you could program it to creep VERY slowly forward. So slow that you don't use up all the movement in your springloaded center. Or indeed very...
  22. Replies
    7
    Views
    953

    That is something special. Either custom by...

    That is something special. Either custom by Sauter or someone else. That turret has some sort of VDI coupling in the variants I have seen.
    Maybe built so it could share tooling with an older machine...
  23. Replies
    24
    Views
    2,397

    I finally got the live tools that was to come...

    I finally got the live tools that was to come with the machine. The bad is that it took months, the good is that I got to order whatever I wanted (6 pieces), and I got 2 extra 6000rpm Sauter radial...
  24. FS: New Mazak axial live tool holder - Through coolant.

    For sale: One brand new axial live tool holder for Mazak bolt-on turret. ER32.
    The inner plastic is sealed and has never been opened.
    Comes with the collet nut and one ER32 collet.
    Fits (among...
  25. Replies
    4
    Views
    861

    Thanks for the ideas and feedback everyone. I...

    Thanks for the ideas and feedback everyone. I thought it was a less complex process to change it so I won't attempt it myself.
    I will try to get Mori to change it first. If that is not working I...
Results 1 to 25 of 930
Page 1 of 38 1 2 3 4