Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: johneezreno

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    1,230

    If I remember correctly there are two formats you...

    If I remember correctly there are two formats you can run that control in. I'd need a manual in front of me to truly recollect. But have you tried? Both of my machines were older. I had a 4020 and a...
  2. Replies
    20
    Views
    1,230

    O12345 (Part bla bla) G00 X Y . . . I've...

    O12345
    (Part bla bla)
    G00 X Y
    .
    .
    .
    I've always listed my program descriptions like such. Hope this helps.

    Sent from my SM-G950U using Tapatalk
  3. Replies
    1
    Views
    509

    Maybe the limit switch is getting sticky? A loose...

    Maybe the limit switch is getting sticky? A loose wire?

    Sent from my SM-G950U using Tapatalk
  4. Yup I agree totally with previous comments. I...

    Yup I agree totally with previous comments. I purchased a warn out Fadal 4020 machine back when I didn't now shit. Machine ran great. XYZ all seemed good. Put some weight on the table and then found...
  5. If it's the same control I have. I found a couple...

    If it's the same control I have. I found a couple YouTube videos that initially helped me out. A guy named Sunpoe or close to that did a great step by step start up and tool offset video.

    Sent...
  6. Replies
    17
    Views
    1,402

    If you're trying to get an incentive plan going...

    If you're trying to get an incentive plan going to motivate your employees, try a profit sharing program. Employee has X# to get job complete. If done in X# employee gets bonus .

    Sent from my...
  7. Not sure if anyone else looked into the initial...

    Not sure if anyone else looked into the initial questioner. But his other topic questions were as good as this one.
    So..... We get a 3D solid model. We import into our Power Mill...... With...
  8. So that would be a big no to the yes'ers? ...

    So that would be a big no to the yes'ers?


    Sent from my SM-G950U using Tapatalk
  9. I guess I got a little lost with the mold makers....

    I guess I got a little lost with the mold makers. I've programmed mills, wires, lathes, wires, and lasers. I have received solid models. But to that extent I wasn't aware I could just throw that...
  10. Oh man, lol. Lots of love. And laugh out loud....

    Oh man, lol. Lots of love. And laugh out loud. They say no question is a bad question. But in some cases. Please put some thought into the question. Even a 3D printer, that most work from a 3D...
  11. Replies
    21
    Views
    1,802

    2 pallets, minimum a pallet n a half 4' 6' 8' ...

    2 pallets, minimum a pallet n a half 4' 6' 8'

    Sent from my SM-G950U using Tapatalk
  12. Replies
    17
    Views
    1,298

    Let us know what control. G70 is a drill cycle in...

    Let us know what control. G70 is a drill cycle in FADAL

    Sent from my SM-G950U using Tapatalk
  13. Replies
    7
    Views
    716

    If you have the manuals, it covers the encoder...

    If you have the manuals, it covers the encoder adjustments. Basically taking cover off of encoding. Loosen the resolve and turn it until your cold start position Mark's line up. There is a height...
  14. Replies
    7
    Views
    716

    Encoder adjustment Sent from my SM-G950U...

    Encoder adjustment

    Sent from my SM-G950U using Tapatalk
  15. I'd start with the basics. Check the micro...

    I'd start with the basics. Check the micro switches and alignment of the switches. If it worked before might just be a sticky switch. I left a creeper behind my machine with the guards off and caused...
  16. Replies
    1
    Views
    447

    Like...

    Like this?https://uploads.tapatalk-cdn.com/20181010/f75d077d344a290c97a4c01ba4de642f.jpg

    Sent from my SM-G950U using Tapatalk
  17. Replies
    9
    Views
    1,100

    Um ya, it's big, has lots of levers. It's clean....

    Um ya, it's big, has lots of levers. It's clean. You one lucky SOB

    Sent from my SM-G950U using Tapatalk
  18. Replies
    12
    Views
    1,046

    From hand to probe..... 10 fold increase. My...

    From hand to probe..... 10 fold increase. My other garage toy is a Brother TC-225 with a conversational control. Truly hate this POS controller. Machine is great. Mis my probe and G-Code control.
    ...
  19. Replies
    12
    Views
    1,046

    I'm sure those answers are in the renishaw how to...

    I'm sure those answers are in the renishaw how to manual. My experience is on a HAAS Mill. I'm currently learning an old FANUC T10 controller on my garage Hitachi Seiki HT-25 lathe. Wish I could be...
  20. Replies
    12
    Views
    1,046

    Lol. Yup did the same thing. Sent from my...

    Lol. Yup did the same thing.

    Sent from my SM-G950U using Tapatalk
  21. Replies
    12
    Views
    1,046

    We used the sleeve from a die set. It's just a...

    We used the sleeve from a die set. It's just a known diameter of a round component.

    Sent from my SM-G950U using Tapatalk
  22. Replies
    10
    Views
    1,025

    I use to run older FADAL, They were out of the...

    I use to run older FADAL, They were out of the game for a bit but also just heard they were back in. HAAS might be a great option also. With probe.

    Sent from my SM-G950U using Tapatalk
  23. Replies
    2
    Views
    860

    The Fryer I ran had a weak / cracked casting that...

    The Fryer I ran had a weak / cracked casting that held X axis ball screw drive.

    Sent from my SM-G950U using Tapatalk
  24. Replies
    36
    Views
    2,662

    I'm in Wisconsin USA. Do you have English version...

    I'm in Wisconsin USA. Do you have English version of manual? Near back of manual they have a step by step process. CMT

    Sent from my SM-G950U using Tapatalk
  25. Replies
    36
    Views
    2,662

    Also after power on. Push M.Z.RT (Machine Zero...

    Also after power on.
    Push M.Z.RT (Machine Zero Return)
    If table over travels and faults out.
    Press / Reset + RELSE together
    And while holding RELSE button move table opposite direction of fault...
Results 1 to 25 of 57
Page 1 of 3 1 2 3