Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Hazzert

Page 1 of 51 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    594

    You can get similar angle boxes from from chinese...

    You can get similar angle boxes from from chinese sources for $10-20. I definitely would not pay grainger's price. All of them seem to have a hold function.

    I have been curious about these two...
  2. Replies
    16
    Views
    839

    Carbide PCB drills can be had in very high number...

    Carbide PCB drills can be had in very high number drill sizes and very affordably and come on a 1/8 or 3mm shank. Maybe they're suitable for your application.

    Edit:
    Looks like post #2 beat me to...
  3. Replies
    10
    Views
    679

    The last time I ran CF we tried DLC coated tools...

    The last time I ran CF we tried DLC coated tools from Niagara and they weren't worth the extra cost. Supposedly they've changed the coating process to make it better but at the time I got the best...
  4. Replies
    10
    Views
    679

    Another name for a 2 flute endmill. A down cut...

    Another name for a 2 flute endmill.

    A down cut bit or a sacrificial topper to support the CF are probably the easy solutions but I've had good luck pecking 3mm holes on size with just a regular...
  5. “We, the unwilling, led by the unknowing, are...

    “We, the unwilling, led by the unknowing, are doing the impossible for the ungrateful. We have done so much, for so long, with so little, we are now qualified to do anything with nothing.”

    Good...
  6. Replies
    30
    Views
    1,285

    How many parts are you trying to fit on a fixture?

    How many parts are you trying to fit on a fixture?
  7. Replies
    30
    Views
    1,285

    I don't have direct experience but I don't like...

    I don't have direct experience but I don't like this plan. A sawcut edge sitting in a pocket with only one contact point on either side of the stock (one pitbull and the pocket) while you profile it?...
  8. Replies
    19
    Views
    977

    Little ironic don't you think?

    Little ironic don't you think?
  9. Replies
    76
    Views
    5,344

    It’s based on your budget, presumably you’re not...

    It’s based on your budget, presumably you’re not making parts that go to space and have had success with a Haas so why jump off the deep end with more machine than you need?

    We have an Okuma...
  10. The worst I’ve seen was a fuel cell compression...

    The worst I’ve seen was a fuel cell compression plate, roughly 20” lo g dog bone shaped with 3d surfaced ports. Pretty much the only tolerances on the part were various profile tolerance GDT callouts...
  11. Replies
    76
    Views
    5,344

    It’s pretty hard to beat something like a...

    It’s pretty hard to beat something like a VF/VM3SS considering your budget. Hell you can get into a UMC750 for about $145k with a 12k spindle.

    I’m not a big Haas fanboy but with them you’d have...
  12. Replies
    43
    Views
    2,715

    That sounds like most modern consumer goods. ...

    That sounds like most modern consumer goods.

    You said that you found hundreds of defects upon inspection. What percentage of previous production would you estimate had (has?) the fault? And if...
  13. Replies
    14
    Views
    1,140

    What kind of stone? I assume carbide would cut...

    What kind of stone?

    I assume carbide would cut most stones to some degree but any inclusions would spell quick death for carbide tooling.

    Maybe look at some cheap diamond points from China or...
  14. Replies
    25
    Views
    2,378

    This is just one of the homegamers that watches...

    This is just one of the homegamers that watches AvEs videos trying to say $700 CAD. It's endearing when he does it and confusing without any of the charm or charisma.
  15. Point your pointer finger to the left and stick...

    Point your pointer finger to the left and stick your thumb straight up so you have a little right triangle. Set it up so that the tip of your finger is the angle you want to find.

    Your thumb is...
  16. How so? Mag base indicators have arms for a...

    How so? Mag base indicators have arms for a reason.

    You can use ether a Tan (opposite and adjacent) trig function


    Tanθ=opposite/adjacent

    θ=arctan(2nd function tan) x opposite/adjacent
  17. Replies
    29
    Views
    2,259

    I think you’re looking at a PCD insert, on the...

    I think you’re looking at a PCD insert, on the bright side if you don’t crash it it should last you quite a while.

    Wind it up as fast as she’ll go you’ll probably break a chip too.
  18. Replies
    5
    Views
    959

    No. Presumably the table is flat(ish) so it’s...

    No.

    Presumably the table is flat(ish) so it’s wear in your ways or saddle etc. Facing the table is only going to provide a perpendicular axis at the position the table was fly cut at. Sounds like...
  19. Replies
    23
    Views
    1,590

    It looks like all those amazon links are...

    It looks like all those amazon links are affiliate links. If anyone were to follow one regardless of what was bought the postee would receive a cut of all the sales made by the clickee for a set...
  20. Replies
    18
    Views
    1,392

    No direct experience but I feel that unless you...

    No direct experience but I feel that unless you were to relieve the side of the wheel to reduce contact you’re more likely to scorch the face plate and should use the periphery of the wheel instead.
  21. Replies
    56
    Views
    4,805

    “Your scientists were so preoccupied with whether...

    “Your scientists were so preoccupied with whether or not they could, they didn’t stop to think if they should.”
    Yeah it’s a curiosity to most but it’s stimulated more interesting content than most...
  22. Replies
    56
    Views
    4,805

    Wire EDM is probably the most economical way of...

    Wire EDM is probably the most economical way of producing an accurate version and would not be particularly limited to width (depth) or material hardness.

    If you just wanted a desktop widget any...
  23. Replies
    6
    Views
    555

    If BobCAD was smart it would calculate the thread...

    If BobCAD was smart it would calculate the thread height for you based on the thread standard selected by the programmer.

    If you are stuck, look up any 20 TPI thread in its library. The value will...
  24. Replies
    29
    Views
    2,119

    You could have wrote it by hand by now and had it...

    You could have wrote it by hand by now and had it to exactly what you wanted.

    Haas has some extra variables on drill cycles but like Mtn said, what machine?
  25. Interesting... I personally use...

    Interesting... I personally use https://www.mscdirect.com/product/details/62691613 and no wrench is included.

    I don't mind pocketing the $300 difference for the lack of wrench and 4mm reduced...
Results 1 to 25 of 1251
Page 1 of 51 1 2 3 4