Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: iwananew10K

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    1
    Views
    481

    shout out for Naru (Stephen)

    268952

    speaks for itself.....only wish i could take better pics..
    this is Stephen's work....that pinion is nicer than original..fantastic quality work!
  2. Replies
    3
    Views
    506

    i can certainly vouch for Stephen.....these are...

    i can certainly vouch for Stephen.....these are some beautifully executed parts....just opened the package today, almost dont want to use that pinion shaft,shame something that nice wont be seen once...
  3. Replies
    12
    Views
    551

    without the threaded leadscrew and halfnuts you...

    without the threaded leadscrew and halfnuts you wont be able to thread anything, you just have differnt feed rates.
  4. hmmmmm...dont think thats factory...likely a...

    hmmmmm...dont think thats factory...likely a special purpose, but dont know what....possibly for a different machine altogether.
  5. yes, that headstock is heavily modified.....as...

    yes, that headstock is heavily modified.....as such its parts are pretty much its parts...but if it works well sell it whole.
  6. Replies
    6
    Views
    397

    yes, thats a different matter, it can be repaired...

    yes, thats a different matter, it can be repaired but replacemnt might be your best option depending.
  7. Replies
    21
    Views
    1,375

    yes, pics of spindle and bearings in particular....

    yes, pics of spindle and bearings in particular.
    dont do anything yet, cant unring that bell once you remove material, though it may prove necessary....if so you dont lap, use a fine file and proper...
  8. Replies
    6
    Views
    397

    i cant recall, but if you are only lacking the...

    i cant recall, but if you are only lacking the taper pin, its a 1 dollar part.
  9. yes, as Mr. Oder noted standard. you can just...

    yes, as Mr. Oder noted standard.
    you can just use MT3 and forget the sleeve too. it might stick out a little too far depending on your set up, but if you buy the cheap centers and view them as...
  10. Replies
    6
    Views
    397

    isnt that for the whole handwheel? those are...

    isnt that for the whole handwheel? those are assembly numbers, meaning more than one part,,in that case the wheel casting with the little handle pressed in.


    you can buy taper pins at most ace...
  11. Replies
    14
    Views
    1,157

    not to be confused with this guy- this guy really...

    not to be confused with this guy- this guy really does rebuild machines.
    Babin Machine Tool
  12. that flange you are missing is no big deal, its...

    that flange you are missing is no big deal, its only pupose it to help keeep crud out the spindle bearing.

    its a press fit and if you want to add it a good lathe project, no hard rule on its...
  13. just securely block up the apron, no need to pull...

    just securely block up the apron, no need to pull gearbox/leadscrew.
  14. Replies
    11
    Views
    1,239

    what is your spindle? 1 3/8" or 1 1/2"...

    what is your spindle? 1 3/8" or 1 1/2" ???.......dont recall the exact date when they switched from the smaller thread nose to the 1.5"x8 tpi but yours is right in the area date wise it could go...
  15. Replies
    14
    Views
    1,612

    maybe the easiest thing you can do is send Ted...

    maybe the easiest thing you can do is send Ted and email, include pic and he will know exactly what you need, and likely can supply the pieces....one stop shopping will save you from multiple...
  16. Replies
    14
    Views
    1,612

    you are missing the- banjo assembly with the...

    you are missing the-
    banjo assembly with the primary and sliding gears
    banjo bed bracket
    Gearbox input gear(64T)

    before you start sinking money tho, would advise a strip down to basic...
  17. Replies
    4
    Views
    866

    might be interested...can't see any pics tho.

    might be interested...can't see any pics tho.
  18. when in doubt,choose the devil you know.

    when in doubt,choose the devil you know.
  19. Replies
    12
    Views
    1,289

    and tailstock.(quill graduations and feed...

    and tailstock.(quill graduations and feed screw/quill nut)
  20. Replies
    29
    Views
    2,559

    18DP....they "might" be the same as workshop...

    18DP....they "might" be the same as workshop series 9".....which are 18DP x 3/8" thick x 9/16" bore IIRC.
  21. Replies
    29
    Views
    2,559

    post up those gear specs...include the face...

    post up those gear specs...include the face width(how "thick")and bore size.
  22. Replies
    8
    Views
    1,526

    not what you are looking for but there is an 11"...

    not what you are looking for but there is an 11" follow rest in the tooling for sale section.
  23. Replies
    29
    Views
    2,559

    provide tooth count and outside diameter of the...

    provide tooth count and outside diameter of the big gear on the bottom and we can determine what gears will work.

    You currently have the fine feed gears in place and are fortunauate to have them,...
  24. Replies
    24
    Views
    2,790

    gonna be down for a bit, but small victories...:)...

    gonna be down for a bit, but small victories...:)

    It's not all buttoned up cause I need to make new shims and set clearances but it's clean and smooth turning , reused the original square wood...
  25. Replies
    10
    Views
    895

    most gun guys seem to like the replaceable brass...

    most gun guys seem to like the replaceable brass tips, otherwise no real advantage I can tell.

    the only personal experience I can give is the tools4cheap steadies were actually quite nice, I used...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4