Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Jim Christie

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. If you can find a wheel with a suitable abrasive...

    If you can find a wheel with a suitable abrasive specification but too large in Diameter or too small in the bore these folks may be able to help.
    Mach-B Grinding Wheel Shaping & Resizing | Winona,...
  2. Since your lathe is smaller and appears lighter...

    Since your lathe is smaller and appears lighter than the one shown in this thread ,...
  3. Replies
    5
    Views
    361

    This photo of yours shows what is usually called...

    This photo of yours shows what is usually called the tumbler reverse lever to the left of the National Engineering dealers plate for reversing the lead and feed screw directions ....
  4. Replies
    6
    Views
    341

    I had tried a search over at vinage machinery and...

    I had tried a search over at vinage machinery and got no results .
    Don't know what I did wrong.
    Jim
  5. Replies
    6
    Views
    341

    The Time Savers machines I know about are...

    The Time Savers machines I know about are thickness sanders .
    If that is what you have ,you might also try posting your request on the woodworking section of the the forum ...
  6. In photo # 3 I see what looks like a part number...

    In photo # 3 I see what looks like a part number stamped in the block on the left above the 0 witness mark for the graduated knob.
    I can’t read the number but someone might recognize it or the...
  7. Dandy Dave , Thanks for sharing the pictures...

    Dandy Dave ,
    Thanks for sharing the pictures from your book.
    I had seen the book mentioned a few times on this forum by JoeinNH and some others and had seen that volume and others y Rose on the...
  8. The small graduated know on the left of the...

    The small graduated know on the left of the first picture looks similar to the ones on the tables stops on my 1950 s Cincinnati Monoset but the rest of the block is not part of anything on a ...
  9. Tom, Thanks For posting the link to the video ....

    Tom,
    Thanks For posting the link to the video .
    I skipped through the video but will go back and view it in full later.
    I noticed several pieces of machinery that were similar to some shown in...
  10. Replies
    20
    Views
    7,486

    I don’t know about the origin of the term but...

    I don’t know about the origin of the term but there is an explanation about some of the types and comparison of the action on the work piece by dogs with and without bent tails.
    It goes on for a...
  11. Thanks Jim , I didn't think to look to see if...

    Thanks Jim ,
    I didn't think to look to see if there were other posts about him elsewhere on the internet before posting.
    Here are a couple of links but a little more searching may turn up more....
  12. Replica WW2 Planes Built From Recycled Materials

    thought some who visit this site might like to see this.
    Even though the link was shared here ,
    Plane savers Public Group | Facebook
    airplanes aren’t the only thing he builds.
    Replica WW2 Planes...
  13. The other switch on your machine lower down looks...

    The other switch on your machine lower down looks like some of the Klockner Moeller switches that are on some of my machines....
  14. Replies
    29
    Views
    1,565

    Here are some pictures from the 1977 S & S....

    Here are some pictures from the 1977 S & S. Machinery Catalogue showing the machine and some of the others available at the time .
    S.& S. was located in the Montreal Quebec area.
    I believe the...
  15. Replies
    29
    Views
    1,565

    Here are some more pictures of mine made that...

    Here are some more pictures of mine made that says made in 1976
    The bull gear was shattered in at the hub and so my father put a plate behind to strengthen it.
    The connecting rod was also broken...
  16. Replies
    29
    Views
    1,565

    I hadn’t noticed that but I think Mike is right....

    I hadn’t noticed that but I think Mike is right.
    It would likely run more smoothly and quietly with helical gears.
    Mine definitely has straight teeth.
    More later .
    Jim
  17. Replies
    29
    Views
    1,565

    I have a saw made in Taiwan that is perhaps made...

    I have a saw made in Taiwan that is perhaps made in the same place as yours or they are cloned or evolved from a similar original .
    I thought i had posted about this somewhere on the this forum...
  18. Replies
    44
    Views
    2,214

    Rick A54, Thanks for posting and sharing the...

    Rick A54,
    Thanks for posting and sharing the information and history .
    Regards ,
    Jim
  19. Replies
    15
    Views
    4,278

    The broken part on yours would have looked ...

    The broken part on yours would have looked something like the one in the link below for a South Bend.
    Le pièce brisé sur votre machine paraitra semblable de celui dans le dessin qui est pour un...
  20. Replies
    15
    Views
    4,278

    It looks like the handle with the retractable pin...

    It looks like the handle with the retractable pin to engage the holes in the gear box on the gear box tumbler gear lever is broken off and missing.
    I’m guessing it would look similar to the Tumbler...
  21. Replies
    15
    Views
    4,278

    Je ne peut pas voir les phots sur l’autre site....

    Je ne peut pas voir les phots sur l’autre site.
    Si vous pouvez les mettre ici ca sera plus facile pour nous a vous aider.
    John Oder a indiquer les manivelles pour le chariot et le tablier.
    Avec...
  22. A similar setup is described here. International...

    A similar setup is described here.
    International Library of Technology : International Textbook Company : Free Download, Borrow, and Streaming : Internet Archive
    I think that in some cases these...
  23. I now remember seeing the popular Mechanics...

    I now remember seeing the popular Mechanics article in one of the Shop Notes reprints I have .
    I had been thinking I had seen some others in a different magazine and found the link I had posted here...
  24. This link about the Canadian Fairbanks Co. and...

    This link about the Canadian Fairbanks Co. and their warehouse in Toronto from 1906 turned up in my files when I was searching for something else .
    Canadian machinery and metalworking...
  25. Newark Engineering and Refrigerating Co. Newark N.J. Filing Machine

    Newark Engineering and Refrigerating Co. Newark N.J. Filing Machine
    A short description and small picture of this machine turned up here
    Canadian machinery and metalworking
    while I was checking...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4