Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: CarlBoyd

Page 1 of 32 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    840

    I have a ruger single six with one tight chamber...

    I have a ruger single six with one tight chamber in the LR cylinder. Clean it chambers OK. after firing about 4 cylinders it gets tight. It's been that way since new in 1986. I have developed a...
  2. Replies
    3
    Views
    503

    Depends on what you want. Do you just want...

    Depends on what you want.

    Do you just want decorative scrapping, or do you need 40 points per inch bearing?
    What are the shapes like? Square/rectangular is easier/cheaper than convoluted shape.
    ...
  3. Replies
    6
    Views
    1,060

    What are the tolerences

    Hi

    Your drawings do not specify the tolerances, every 0 to the right of the decimal point increases the price, a lot. I suspect ±0.03" or 1/32" is adequate for what you need.

    CarlBoyd
  4. Super idea! Kick him in the balls. CarlBoyd

    Super idea!

    Kick him in the balls.

    CarlBoyd
  5. Replies
    25
    Views
    1,150

    Green sand filter, similar to water softener,...

    Green sand filter, similar to water softener, recharged with potassium permanganate. Removes iron and sulfer.
    Mine is ancient, manual recharged, 1/2 cup of potassium permanganate every 3 or 4 week.
  6. Replies
    6
    Views
    631

    Sorry to hear you lost your dad. Best way to...

    Sorry to hear you lost your dad.

    Best way to price anything is to look on ebay for sold listings of the same or similar item. You will get more money if you sell separately, but more hassle.
    ...
  7. Every bench grinder I have ever used get's hot,...

    Every bench grinder I have ever used get's hot, grind on.

    CarlBoyd
  8. Replies
    39
    Views
    2,538

    Let me rephrase your question. Can I be less...

    Let me rephrase your question.

    Can I be less careful with a lathe that can only maim me?

    Think about it.

    CarlBoyd
  9. Bad Idea, How much can you sell what you have,...

    Bad Idea, How much can you sell what you have, and how much to buy 16 footers, how much time to cobble together and weld, and what bad stuff happens when the joint fails. Are you a welder by trade?...
  10. Replies
    3
    Views
    1,040

    I'll do it for shipping if you remember me when...

    I'll do it for shipping if you remember me when you need something that could be profitable.
    Give me your address.

    CarlBoyd
  11. SWAG unbalanced so you get 3 choices of...

    SWAG unbalanced so you get 3 choices of impedance, center tapped would only give you 2.
    Tubes outputs are much higher impedance than transistors and impedance matching is critical for max power...
  12. Early Cappuccino Machine? CarlBoyd

    Early Cappuccino Machine?

    CarlBoyd
  13. Replies
    43
    Views
    4,135

    He either pays you now, or pays back wages for...

    He either pays you now, or pays back wages for all the unpaid overtime you have worked the past.

    CarlBoyd
  14. Replies
    13
    Views
    1,279

    My day job is in the electrical domain. We have...

    My day job is in the electrical domain. We have the same 10 to 1 rule of thumb. When you can meet the 10 to 1 rule, you can ignore measurement error. When you can't, or when it's impractical (i.e....
  15. disk magnets over the holes CarlBoyd

    disk magnets over the holes

    CarlBoyd
  16. Replies
    33
    Views
    2,160

    Drill a big hole in the mortor, fill with better...

    Drill a big hole in the mortor, fill with better mortar, let set, re-drill, install tapcon.

    CarlBoyd
  17. Replies
    32
    Views
    2,376

    Oh, for crying out loud, go back and get the band...

    Oh, for crying out loud, go back and get the band saw.

    Wait a minute, where in GA?

    CarlBoyd
  18. Replies
    521
    Views
    23,717

    Pretty basic physics, any figure skater can tell...

    Pretty basic physics, any figure skater can tell you the answer. I suspect and would hope you already know the answer. The earths rotational speed would decrease.

    CarlBoyd
  19. Replies
    37
    Views
    4,903

    Private Message coming CarlBoyd

    Private Message coming

    CarlBoyd
  20. I haven't had Branston pickle in a coons age, now...

    I haven't had Branston pickle in a coons age, now I need to chase some down.

    CarlBoyd
  21. The surge brake trailers I have seen have a pin...

    The surge brake trailers I have seen have a pin or latch you can engage to disable the brakes when backing up.

    CarlBoyd
  22. Dewatering the ground might be a solution. It...

    Dewatering the ground might be a solution. It would require pumps to run constantly.

    CarlBoyd
  23. Replies
    5
    Views
    821

    I'll take the radius gages. CarlBoyd

    I'll take the radius gages.

    CarlBoyd
  24. 5 6 7 is not a right triangle. Pythagorean...

    5 6 7 is not a right triangle. Pythagorean theorem.

    CarlBoyd
  25. Replies
    8
    Views
    3,374

    I'd like to work with you on this, PM coming. ...

    I'd like to work with you on this, PM coming.

    CarlBoyd
Results 1 to 25 of 796
Page 1 of 32 1 2 3 4