Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: dana gear

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Check out Welding Direct.com Cebora makes...

    Check out Welding Direct.com
    Cebora makes plasma power sources badged for several different company's plasma product line.
    I have never used Cebora power sources but have been told there fair...
  2. Replies
    30
    Views
    865

    You won't be displeased with the Metabo, Years...

    You won't be displeased with the Metabo, Years back a Metabo rep came to our shop's with a couple of 4 and 9 inch grinders.
    We were actually told to work them as hard as possible, just short of out...
  3. That was very kind of Lincoln Electric to provide...

    That was very kind of Lincoln Electric to provide you with a take off controller board.
    There are two versions of the V-205 a strictly DC unit and an AC/DC unit, that do use different display units....
  4. Replies
    19
    Views
    835

    Most welding supply stores will swap out those...

    Most welding supply stores will swap out those cylinders. Heating and air guys use the heck out of them. That is a plumbers out fit, copper soldering and even very old world...
  5. Replies
    1
    Views
    186

    There a good overall feeder. 24 volt drive...

    There a good overall feeder. 24 volt drive system. does your feeder still have the brain cable attached to it?
    The amprenol plug it will plug right into the XMT. It is compatable to a bunch of...
  6. Replies
    5
    Views
    437

    HDPE/LDPE, Put the shear where you want it and...

    HDPE/LDPE, Put the shear where you want it and shear away.
  7. Replies
    5
    Views
    377

    We use Uni Hydro and Scotchmen Iron workers,...

    We use Uni Hydro and Scotchmen Iron workers, nothing as small as the 45, that said we have had both Uni Hydro and Cleveland punch and die build us custom clearance and diameter punch and die sets....
  8. Replies
    14
    Views
    802

    We have an old South bend that is set up to weld...

    We have an old South bend that is set up to weld shaft or what ever round. we fabricated a frame that used 4 Large carbon brushes for a Lincoln SAE 400 and even used Lincoln spring loaded brush...
  9. Replies
    43
    Views
    3,091

    There have been over the years many discussions...

    There have been over the years many discussions as to the real intent of the Hughes Glomar explorer.
    The Hughes USNS Glomar explorer was a deep sea drilling platform code named Azorian by the...
  10. Back in the stone age when I started working in...

    Back in the stone age when I started working in the shop there was 2 giant safety pin looking things(Best way to describe them) that held probably 30 spark testing rods each, the rods had a small...
  11. Replies
    43
    Views
    3,091

    A consortium between the American Central...

    A consortium between the American Central intelligence agency CIA and the Hughes corporation, Hughes had the means and the CIA wanted the cover story that the ship has for deep sea oil exploration....
  12. Replies
    18
    Views
    3,138

    Last year we replaced a 1950 era Chicago D&K 500...

    Last year we replaced a 1950 era Chicago D&K 500 ton hydraulic press brake with 7' bed with 6'of day light.
    Pretty nice machine overall, it used a tape wire to control travel of stroke between the...
  13. We purchased two Ingersol Rand unigy VFD rotary...

    We purchased two Ingersol Rand unigy VFD rotary screw compressors as replacements for earlier units. MAJOR piles of pure junk.
    We got to know the I/R warranty guy real well, when the warranty ran...
  14. Replies
    7
    Views
    437

    If the ram rod diameter is 2.375 and the...

    If the ram rod diameter is 2.375 and the hydraulic cylinder inside diameter is 6" then at 1200 psi you would get around 33,929 push and 28,613 pull. At 1500 psi then 42,411 push,35,766 pull. These...
  15. Replies
    31
    Views
    1,541

    I could no longer understand my 7 year old...

    I could no longer understand my 7 year old granddaughter any more and my poor wife pretty much repeated every other sentence.
    I started out trying a pair of hearing aids that cost close to 4 grand...
  16. Replies
    14
    Views
    895

    Absolutely fantastic machine that will at the...

    Absolutely fantastic machine that will at the very least last a couple of life times.
  17. Replies
    11
    Views
    1,041

    What's not right on your bobcat?

    What's not right on your bobcat?
  18. Just pointing out that a simple adjustable...

    Just pointing out that a simple adjustable apprentice for cutting different disc sizes on a Heath pattern cutter would probably be hard if not impossible to hold very close tolerance, if a very tight...
  19. Replies
    7
    Views
    683

    Glad you got it going, Just remember that stick...

    Glad you got it going, Just remember that stick welding (SMAW) constant current will require contactor on and that if your using a remote control for GTAW welding then switch from panel to remote. If...
  20. Replies
    7
    Views
    683

    The 300 is a dirt simple power source and the 22A...

    The 300 is a dirt simple power source and the 22A is a great industrial feeder. Check ALL cable connections then check that the electrode wire will coil up in your gloved hand held about 7 inches...
  21. Replies
    159
    Views
    14,556

    Well it does not look like the load test went...

    Well it does not look like the load test went well. I guess better there then with something important on the hook.
  22. Replies
    12
    Views
    881

    I have no idea what the set is for, that said...

    I have no idea what the set is for, that said some of the drivers are for anti-tamper fasteners.
  23. We installed a Norton tool/cutter sharpening...

    We installed a Norton tool/cutter sharpening grinder in the shop,when the pile of used cutters gets to large we go through the used cutters and only re-sharp 5/8" and larger that still look...
  24. One consideration is how accurate plus/minus...

    One consideration is how accurate plus/minus diameter do your circles need to be.
    It may be hard to hold circular dimension if that's a concern.
  25. Replies
    19
    Views
    1,314

    We paint stick or stamp in two places the...

    We paint stick or stamp in two places the type/grade of all steel rems that don't make it to the scrap box and end up back in our storage. I have wondered how many times our local scrap yard may have...
Results 1 to 25 of 287
Page 1 of 12 1 2 3 4