Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: NewToEDM

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    524

    Thanks :) Will have to order that part anyway ,...

    Thanks :)
    Will have to order that part anyway , and i have no code for it :(
  2. Replies
    2
    Views
    524

    Microfilter pneumatic plate

    Hi , i am working on a AgieCharmilles CUT E 350 and i need to replace some consumables .Can't find any info in user manual for the microfilter pneumatic plate.
  3. Replies
    7
    Views
    1,022

    Thanks for your reply Found that after i looked...

    Thanks for your reply
    Found that after i looked at some scheme for the machine , it was 1.64 (max 2.8)
    I wrote steps i followed just in case it will be helpful for someone as noob as i am.
    Good day
  4. Replies
    7
    Views
    1,022

    Pump was dry , filled with water and started....

    Pump was dry , filled with water and started.
    And few touches here and there
    Machine works , hopefully will do the job overnight
  5. Replies
    7
    Views
    1,022

    cooling system doesn't work , any switch i don't...

    cooling system doesn't work , any switch i don't know about ?
  6. Replies
    7
    Views
    1,022

    Pressure was 1.6 Filters changed Waiting to get...

    Pressure was 1.6
    Filters changed
    Waiting to get back to normal
  7. Replies
    7
    Views
    1,022

    filter pressure

    Help
    Where i can check filter pressure on Cut E 350 ?

    Default time for them to be changed at 1000 hours , i have 440 now
    Got an error - filters obstructed , chiller error - fluid shortage ...
  8. Thread: 4 axis cut

    by NewToEDM
    Replies
    2
    Views
    586

    I am waiting for a reply from them Error is...

    I am waiting for a reply from them
    Error is "Axis acceleration exceeds maximum limit"
    It stops while working , no error when i load the program
    The part i work on is 15 x 5 x 40 mm , one side has...
  9. Replies
    4
    Views
    989

    Any ideea what would work on CMM Mitutoyo Crysta...

    Any ideea what would work on CMM Mitutoyo Crysta Plus 544 ?
  10. Thread: 4 axis cut

    by NewToEDM
    Replies
    2
    Views
    586

    4 axis cut

    Hi
    I run a Cut E-350 , i am programming with Visi
    Made a 4 axis program and i couldn't run it on the machine
    I started the machine and i had 2 error codes - CNB 50120 and EXM 0108 and 1 warning...
  11. Replies
    1
    Views
    574

    to open a .step format document and measure on...

    to open a .step format document and measure on the part , to do a cnc measuring program , to use the machine at full potential
    i need a program compatible with my machine , one that is on the market...
  12. Replies
    1
    Views
    574

    Mitutoyo Crysta Plus ( 544 )

    hello everyone
    anyone knows what program i could use to run a cnc measurement from data ?
    a walkthrough , some basics
    any help would do
    thank you
  13. Thread: starthole

    by NewToEDM
    Replies
    2
    Views
    780

    the lower z axis switch wasn't working , spring...

    the lower z axis switch wasn't working , spring wasn't tense enough but i bend it a bit and now it works
    sadly that didn't solved the problem
    we have measured for short circuit , sadly we have one...
  14. Thread: starthole

    by NewToEDM
    Replies
    2
    Views
    780

    starthole

    hi
    we have bought an old starthole punching machine
    WDS SB-1M
    at first contact with the piece it makes a spark and that high note sound
    and goes back up
    what could be the problem ?
  15. when i had this high pitch noise it was because...

    when i had this high pitch noise it was because i've tightened the upper contact too strong after i have turned it .
    but i run an Agie Charmilles
  16. Replies
    24
    Views
    6,833

    i have only changed the big filters , upper level...

    i have only changed the big filters , upper level sensor in clean water tank , and besides that i have only cleaned the dirty water tank and the working area . i haven't opened anything else .

    do...
  17. Thread: wire Edm e350

    by NewToEDM
    Replies
    6
    Views
    1,063

    it was my mistake , i had screwed too tight the...

    it was my mistake , i had screwed too tight the upper guide and it had too much contact with the wire
  18. Thread: wire Edm e350

    by NewToEDM
    Replies
    6
    Views
    1,063

    i only have problems threading when outside the...

    i only have problems threading when outside the part and higher than the part , depends on geometry . i had a part with a start hole of .3 and it worked with my .25 wire , so yes , has good threading...
  19. Thread: wire Edm e350

    by NewToEDM
    Replies
    6
    Views
    1,063

    i switched to Brass 900 , with this one it lets...

    i switched to Brass 900 , with this one it lets me use this hight.
    i have tried and changed wire 0.3 ( just in program to make a test ) but that wire type is still on grey.
    and about visi , i am...
  20. Thread: wire Edm e350

    by NewToEDM
    Replies
    6
    Views
    1,063

    wire Edm e350

    Hi , i am new in this field . i work on a wire and on a sink machine and i will start to use a fast punch hole machine also
    the wire machine is an AgieCharmilles CUT E350 , i work with the machine...
  21. Replies
    24
    Views
    6,833

    Hi , i am new in this field . i work on a wire...

    Hi , i am new in this field . i work on a wire and on a sink machine and i will start to use a fast punch hole machine also
    the wire machine is an AgieCharmilles CUT E350 , i work with the machine...
Results 1 to 21 of 21