Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cole2534

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    541

    Wish we could instill more of that here.

    Wish we could instill more of that here.
  2. That's similar to what I did. I took a...

    That's similar to what I did. I took a measurement of much would need removed to get every thing square, then rounded up to the next size shim stock. I think I needed to remove .022" but ended up...
  3. Is it possible that Mach3 is set to dwell in...

    Is it possible that Mach3 is set to dwell in seconds and that the dwell value is so high that the controller disregards that line?

    Sent from my SM-G973U using Tapatalk
  4. Replies
    36
    Views
    49,243

    I'm sure there's a difference but I've not...

    I'm sure there's a difference but I've not noticed it. What brands does everyone recommend?
  5. Replies
    9
    Views
    553

    You may try playing with the entry/start points...

    You may try playing with the entry/start points in the Adaptive cycle. If I don't select one a specific point then it randomly enters the part where it feels like it. What does it do if you attempt...
  6. You're right, I hadn't yet watched the video.

    You're right, I hadn't yet watched the video.
  7. Have you checked your work lead for good...

    Have you checked your work lead for good connection? If that's no good you could be running on only the pilot arc and that would explain it turning off at prematurely.

    Sent from my SM-G973U...
  8. Are quality 2J collets hard to come by? Sent...

    Are quality 2J collets hard to come by?

    Sent from my SM-G973U using Tapatalk
  9. Probably a stickout/diameter ratio would be best....

    Probably a stickout/diameter ratio would be best. For steel, a 1" bar sticking out 12-18" doesn't bother me at low speeds like <500 rpm. But I dont think I'd try that for plastic.

    Sent from my...
  10. Thread: $40 dro

    by Cole2534
    Replies
    10
    Views
    706

    An electronic scale that reads/repeats to +/-...

    An electronic scale that reads/repeats to +/- .002"? Sure $40 will probably get you one.

    But a good DRO is much more than a positional readout. It will calculate bolt circles and angular arrays,...
  11. Replies
    7
    Views
    586

    Whew. Better call State Farm. ...

    Whew. Better call State Farm.

    https://s3.eu-central-1.amazonaws.com/vertikal.net/11_img-0684_2bb5bc03.jpg
  12. Replies
    103
    Views
    5,078

    I appreciate your assessment. Concise, succinct...

    I appreciate your assessment. Concise, succinct and focused on the actual topic- tool promotion.

    Is there a single word for that so that I may use it in emails? :)
  13. Replies
    28
    Views
    1,623

    This ^^^^^ is definitely the way to go.

    This ^^^^^ is definitely the way to go.
  14. Which is just another bullshit ATF number like...

    Which is just another bullshit ATF number like 16" or 10rds.

    Sent from my SM-G973U using Tapatalk
  15. Any other coplanar studs? That could form the...

    Any other coplanar studs? That could form the basis to attach a subplate and use a mag drill to remove the stud if it's not easy to fit into a mill.

    Sent from my SM-G973U using Tapatalk
  16. Replies
    7
    Views
    586

    I did that, was hoping some here had more detail....

    I did that, was hoping some here had more detail.

    Sent from my SM-G973U using Tapatalk
  17. Replies
    7
    Views
    586

    South Dakota crane topple

    Anyone seen any good info on Buckner's LR-11000 that went over backwards in SD recently?
  18. The forum about transformers and electrical...

    The forum about transformers and electrical stuff.

    Sent from my SM-G973U using Tapatalk
  19. Replies
    5
    Views
    415

    So the operator and contacts can be isloated? ...

    So the operator and contacts can be isloated? That's neat.

    In OKC we have a surplus shop strictly for industrial electric, maybe something like that could help you search?

    Sent from my...
  20. Replies
    28
    Views
    1,623

    I put a delrin nut in my monarch when I redid the...

    I put a delrin nut in my monarch when I redid the x slide screw years ago. It's easy, it's accurate, but...it sucks for knurling. The high tool pressures and plastic nut make getting a good knurl...
  21. Replies
    15
    Views
    1,007

    Do your own rigging and use a heavy wrecker to do...

    Do your own rigging and use a heavy wrecker to do the lift. Ive done this several times, last of which was $200 to pick/set 3 machines.

    I'd really consider going back to a fadal solely for the...
  22. Well that's interesting. Sent from my...

    Well that's interesting.

    Sent from my SM-G973U using Tapatalk
  23. Replies
    13
    Views
    803

    Get a 4mt tool holder to hold your drills, feed...

    Get a 4mt tool holder to hold your drills, feed with carriage.

    No, I'd not go about cutting on either of those features on the lathe unless absolutely necessary.

    Sent from my SM-G973U using...
  24. Replies
    55
    Views
    38,942

    Dang Bob, no love for 4140ht? Sent from my...

    Dang Bob, no love for 4140ht?

    Sent from my SM-G973U using Tapatalk
  25. Replies
    8
    Views
    520

    If someone doesn't want the whole shebang, I'd...

    If someone doesn't want the whole shebang, I'd LOVE to have the bad clamp only. Flat rate box, will pay shipping!

    Sent from my SM-G973U using Tapatalk
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4