Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: d'Arsonval

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    71
    Views
    4,745

    One of the definitive "bibles" on job seeking,...

    One of the definitive "bibles" on job seeking, resumes, etc... that has been in publication annually since 1975... and has sold more than ten million copies to date
    is the book titled, "What Color...
  2. In the world of failures, a term known as "Root...

    In the world of failures, a term known as "Root Cause Analysis" exists.

    It seeks out the true cause for something failing. The gear appears to have been held fast or obstructed from tuning freely....
  3. Replies
    16
    Views
    1,635

    The wrecker at Liberal, Kansas is a Type X...

    The wrecker at Liberal, Kansas is a Type X 160-ton crane... first developed in 1915 by Industrial Works, Bay City, Michigan.

    This particular “Big Hook” represented an increase in capacity from...
  4. Using a Sharpie Extra Fine Point Industrial...

    Using a Sharpie Extra Fine Point Industrial "Super Permanent Ink" black marking pen,
    it will take approximately 2 hours and 20 minutes to legibly hand letter a 100 foot long
    conventional steel...
  5. If there is a market for a Wi-Fi connected...

    If there is a market for a Wi-Fi connected barbecue grill and a battery operated adjustable wrench,
    than surely there's a customer out there needing a tape measure marked off completely in inches...
  6. Not everyone can... will... or want to understand...

    Not everyone can... will... or want to understand the reason or purpose for your objective.

    I have altered conventional steel tapes in the past for field work using a "Sharpie" permanent marker....
  7. Replies
    16
    Views
    1,551

    true temper, That old McMaster-Carr catalog...

    true temper,

    That old McMaster-Carr catalog from '52 would indeed be a fun read.
    If you happen to check in on this thread again, I'd be curious to know what
    catalog number a 1952 book would be....
  8. Replies
    16
    Views
    1,551

    The resolution of the catalog pages posted could...

    The resolution of the catalog pages posted could have been better.

    The $18.29 3/8" SPEEDWAY DRILL shown on one of the posted photos has three prices.

    List: $27.50

    Each: $19.25

    Lots 3:...
  9. Replies
    16
    Views
    1,551

    Power Tool Prices in 1951

    Power Tool Prices in 1951

    Some of you may enjoy a look at power tool prices from a Fall 1951 Grainger catalog.
    (The catalog measures about 3/16" in thickness at 101 pages including front and back...
  10. 59-years-old here. This discussion has been...

    59-years-old here.

    This discussion has been fascinating to read. It reminds me of conversations enjoyed around a camp fire or kitchen table.
    Rarely do I read an entire thread from beginning to...
  11. The report about not being able to make a...

    The report about not being able to make a particular screw caught my attention as well when it was published.
    Mostly because I had worked in a screw factory in the ‘90s and could identify with how...
  12. Your 254U frame motor was manufactured between...

    Your 254U frame motor was manufactured between 1952 and 1964.

    John
  13. Replies
    15
    Views
    1,413

    Duh... Ha Ha, it did just occur to me... the...

    Duh... Ha Ha, it did just occur to me... the pulley does not have to be removed from the motor shaft.
    Sorry 'bout that.

    John
  14. Replies
    15
    Views
    1,413

    Ralph, As JST mentions, the motor will have to...

    Ralph,

    As JST mentions, the motor will have to be dismantled to gain access to its internal electrical connections.
    For someone not accustom to this type of task, it will be intimidating.
    ...
  15. Replies
    23
    Views
    3,489

    “We are a small family owned job shop…” ...

    “We are a small family owned job shop…”

    Include your family in the decision, and thinking process.

    Start there.

    John
  16. Steve; The crowd here is correct related to...

    Steve;

    The crowd here is correct related to the connection remaining “hot”.

    (Hence; overload protection, [start-stop] station, disconnect, before the drum switch, etc.)
    Article 430 in the...
  17. From the original post: "...I am attempting to...

    From the original post: "...I am attempting to wire this using the high voltage(240v) configuration..."

    The drawing could have been labeled "HI VOLTS"; 220 Volts, 230 Volts, 240 Volts, or as it is...
  18. I’m gaining something from your replies. Thank...

    I’m gaining something from your replies. Thank You.

    Perhaps another way of refining the question requires some name dropping.

    Thomas Edison – Inventor
    Howard Hughes- Aviator

    Jack Welch-...
  19. Yes, there is a way to connect your Dayton drum...

    Yes, there is a way to connect your Dayton drum switch to the motor shown in your nameplate photo.

    Based on the amp draw ratings viewable, I’m guessing the motor is a 3/4 HP rated for 115 /...
  20. What Best Represents the Core of [the] Business?

    What best represents the Core of [the] business?

    Is the core of the business its subject matter/knowledge base… (Its Product and Service)?

    Or, is it the administration of the...
  21. Pete; Your question of “…forum as a long term...

    Pete;

    Your question of “…forum as a long term reference source?” is superb.

    It moved me to Log In… which I’ve evidently not done since 2011.
    (Had to find my password and so on.)

    It looks...
  22. Replies
    15
    Views
    2,891

    Where are the Safety Glasses?

    The opening scenes in this CBS Sunday Morning program caught my eye right away.

    No one in this GM automobile manufacturing plant is wearing safety glasses.
    ...
  23. Replies
    6
    Views
    1,981

    Employee On-Line Presence

    Employee On-Line Presence

    There have been numerous posts regarding the on-line presence of "Business" for sake of business.
    Building a polished web-site (for example) that best represents a...
  24. Replies
    4
    Views
    5,523

    As Soon as I saw the number 3003, as it relates...

    As Soon as I saw the number 3003, as it relates to machining ALUMINUM,
    I got a vibe on why you may not be receiving any replies... as of [YET] on this post.

    No, it's not because everyone has gone...
  25. Thank You Bill. And Scott, I actually do have...

    Thank You Bill.

    And Scott, I actually do have a few framed and on the wall.
    I'm with 'ya on the "nah" to a CAD image.

    Joe, I read with great interest the URL to the New York Times article. ...
Results 1 to 25 of 29
Page 1 of 2 1 2