Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Scruffy887

Page 1 of 59 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    5
    Views
    599

    Use a TIG welder. Be aware that the piece...

    Use a TIG welder. Be aware that the piece sticking out may or may not be connected to the rest of the tap below. They sometimes shatter.
    Wit TIG torch melt the tap end just a small bit and then...
  2. Replies
    6
    Views
    1,455

    I purchased from a West coast importer who did a...

    I purchased from a West coast importer who did a complete package deal. Price was for machine delivered to my East coast shop and complete installation and training. I had to unload and get it in the...
  3. Replies
    19
    Views
    1,268

    Cutting with Oxy as an assist gas will give very...

    Cutting with Oxy as an assist gas will give very different results than cutting with Nitrogen in steels.
  4. Hunter makes nice machines. I bought one off...

    Hunter makes nice machines. I bought one off fleabay and called the local Hunter rep to check it out. Said good machine, would you like to buy some parts? Cash for a discount? Bought a few Duck heads...
  5. Replies
    109
    Views
    5,957

    We have 2 somewhat squirrel proof bird feeders...

    We have 2 somewhat squirrel proof bird feeders and we also scatter seed for ground feeders. Fair amount of squirrels show up and as long as there is ground seed they chew and screw. Fox den nearby...
  6. Replies
    19
    Views
    1,268

    Hardening only goes so far and tooling is...

    Hardening only goes so far and tooling is affected to a certain amount.
    I don't know why Digger did not say that. LMAO
  7. Replies
    21
    Views
    2,399

    I think I paid about 900 for this table top and...

    I think I paid about 900 for this table top and made my own base. It is in the low position now but can be lifted by forklift and then it will be about 36" high. 29.5" x 69". I have a lot of clamping...
  8. I have done the twist off by accident. Worked...

    I have done the twist off by accident. Worked good too. But for my use I stepped the outside of the sub jaws for clearance and use a standard blade type chip holder.
  9. Replies
    20
    Views
    2,048

    Description sure sounds like a laxative.

    Description sure sounds like a laxative.
  10. Thread: Need help

    by Scruffy887
    Replies
    28
    Views
    1,528

    SW can be dialed in to give you almost exactly...

    SW can be dialed in to give you almost exactly what you want and corner gaps are adjustable. Bending is out of your control so you need to work with THEIR parameters to get what you want. I have SW...
  11. Replies
    23
    Views
    3,060

    Zero rake and all should be fine. On the lathe I...

    Zero rake and all should be fine. On the lathe I peck feed and need to pull out completely to clear chips. On the mill the peck distance is about same as drill D to start, dwell peck. I want the...
  12. Perfect job for a laser, apply finish first. 3M...

    Perfect job for a laser, apply finish first.
    3M makes some really good abrasive brushes in cup and wheel form. And they last a real long time.
  13. Replies
    23
    Views
    3,060

    Hole that deep on a manual lathe with the...

    Hole that deep on a manual lathe with the tailstock will be a major PITA. Drill on the carriage. Parabolic drill to get chips out but grind the cutting edges flat. If not then it will pull for sure...
  14. Any and all, including 317U unobtainium grade....

    Any and all, including 317U unobtainium grade. Really need more info like sketch and punch and die stuff.
  15. Replies
    40
    Views
    3,843

    Almost finished. All smaller drawers are on 100#...

    Almost finished. All smaller drawers are on 100# soft close full extension slides. Big drawer is on 500# full extension slides.
    262869
  16. Replies
    26
    Views
    3,658

    I can't believe I got half way through these...

    I can't believe I got half way through these replies before it dawned on me that these are soft jaws on a vise. Coffee not working this morning.
    Multiple parts stacked in lathe jaws made no sense.
  17. Replies
    45
    Views
    4,708

    Supplier of mine said this. If its going to be...

    Supplier of mine said this. If its going to be late, its Yellow Freight. Not dependable and F them. We will not use them and suppliers are forbidden to use them to ship to us. As a noob I loaded 3...
  18. Replies
    23
    Views
    2,119

    You guyzs forgot unobtainium. Flux capacitor...

    You guyzs forgot unobtainium. Flux capacitor needed w/o gas.
  19. Replies
    4
    Views
    623

    Does it say which side is lowest? Rotate the die...

    Does it say which side is lowest? Rotate the die and see if the problem switches sides. Could also be density differences on the die.
    Try putting the tooling in the middle. You are loading lop sided.
  20. Replies
    10
    Views
    1,132

    Once the coating is gone the tool is toast....

    Once the coating is gone the tool is toast. Carbide does not hold up to quartz very well. You really want the diamond/metal matrix as per DavidScott and you will need a rougher and a series of...
  21. No offence to DD but listening to failures only...

    No offence to DD but listening to failures only has problems with your perception. I stopped breathing only 89 times an hour at my last sleep study. Report also said I did not tolerate the nasal mask...
  22. Wife and I each drive Ford Focus RS AWD hatch...

    Wife and I each drive Ford Focus RS AWD hatch backs. 6 speed, Recaro seats, Brembo brakes, and 350 HP. 4 driving modes, normal, sport, drift, track. In drift mode 80% power goes to the rear and 20%...
  23. Replies
    14
    Views
    1,241

    Granquartz.com or Regentstoneproducts.com Both...

    Granquartz.com or Regentstoneproducts.com
    Both will have plenty of diamond tools. Stay away from any type of chip forming tool unless working with soapstone, marble.
  24. Replies
    26
    Views
    1,777

    Looking at blue circle. Do I see L1, L2, L3 and...

    Looking at blue circle. Do I see L1, L2, L3 and ground at the big relay? 3 phase if so.
  25. Replies
    26
    Views
    1,777

    Not sure about single phase 220/440. That would...

    Not sure about single phase 220/440. That would describe a motor that could run on single phase 440 volts?
Results 1 to 25 of 1451
Page 1 of 59 1 2 3 4