Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: snowman

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. The answer is so dependent upon the details. ...

    The answer is so dependent upon the details.

    What machine?

    What opening?

    I can get an extra inch taking the right meds.

    An extra couple if I take the door jam off first.
  2. Replies
    8
    Views
    495

    I am pretty sure it's ignition related...I left...

    I am pretty sure it's ignition related...I left the seat up on it yesterday after looking at vacuum lines. It poured a bit, and now it won't start at all. And the more I think back, the hardest...
  3. Kennametal kentip 8 mm 1.5x chamfer drills

    *I believe* this is an 8mm kentip holder w/chamfer insert built in.

    12mm shank (i think), oal of just over 3"

    i've got at least 20 of them, and you'll get a screaming deal if you need them ($10...
  4. FS Little carbide tool holder for welding / assembly in to cheap tool holders

    Anybody need something like this?

    It's a crowley custom tool holder.

    OAL is under an inch. 1/2" wide holder.

    Not sure what the insert is..

    5 of them for $15 shipped to you
  5. Too bad...I thought this thread was actually...

    Too bad...I thought this thread was actually active again.

    I too have been prescribed similar activities for my anxiety/depression.

    My shrink believed it would help me get out of my own head,...
  6. Replies
    8
    Views
    495

    Hard to start, rough running LPG forklift

    Nissan LPG forklift.

    Either starts really hard, or doesn't start...then idles really rough.

    I've never really worked on anything LPG powered...if it was gas I would have already cleaned the...
  7. Well...after all that, I finally dug in to it. ...

    Well...after all that, I finally dug in to it. Meaning dug it out of the corner. Seems the first layer of wire had rusted, and that had loaded up the wire feed roller with nasty rusty dirt which...
  8. Thread: OSHA results

    by snowman
    Replies
    64
    Views
    8,097

    What's the saying...don't let your mouth write a...

    What's the saying...don't let your mouth write a check your ass can't cash?

    I'm quite sure his ass was a little sore after that vocal session.

    So...I guess he got away with it, in that he...
  9. Thread: OSHA results

    by snowman
    Replies
    64
    Views
    8,097

    I worked for a company that actually had a...

    I worked for a company that actually had a business owner fire someone AFTER they reported him to osha because he screwed them over on a raise or something. He admitted it in court.

    Then he...
  10. Replies
    27
    Views
    2,642

    Venture capitalists are nice when you are selling...

    Venture capitalists are nice when you are selling your business to retire, and have done your homework to know how to make your company attractive.

    Beyond that, I can’t think of many times that...
  11. In a manufacturing environment, it was all quoted...

    In a manufacturing environment, it was all quoted by two shops unless it was a 911 job. When one shop did all the work for six months straight, it started to get difficult to get other shops to...
  12. Replies
    27
    Views
    2,642

    Ok....so not as much expanding capacity as...

    Ok....so not as much expanding capacity as growing floor space.

    That completely makes sense....hell, most of us could probably double in size just by moving a couple holes on the belt!!!



    ...
  13. Replies
    27
    Views
    2,642

    Curious about the "double your factory size". ...

    Curious about the "double your factory size".

    Is that, don't ease into growth, or don't go bigger than 2x what you have now?...because it seems to be don't ease in to growth, and I'm a bit...
  14. Replies
    26
    Views
    2,786

    When I list on eBay, I reach a worldwide audience...

    When I list on eBay, I reach a worldwide audience for 13% of gross sale. That's a really really low operating cost. All I have to do is put it in a box and slap a label on it.

    I don't find...
  15. Everyone should have received ship notification...

    Everyone should have received ship notification from paypal.

    Actual shipment will go out in tomorrows mail.
  16. Everyone should have received ship notification...

    Everyone should have received ship notification from paypal.

    Actual shipment will go out in tomorrows mail.
  17. Thanks...with Dan's, that makes 3 lots. I think...

    Thanks...with Dan's, that makes 3 lots. I think I'm close to out.

    If not, I'll repost in a bit.
  18. Your inbox is full. Got payment (I think),...

    Your inbox is full.

    Got payment (I think), send me a message with your first and last name just so I make I send the right items.

    Had a couple payments for the same amount come in at the same...
  19. With a BA/BS in finance, have you considered...

    With a BA/BS in finance, have you considered engineering technology with a heavy hand on the manufacturing technology side?

    As for sobriety...I generally found that it was when they WEREN'T...
  20. Message sent. Sent from my iPhone using...

    Message sent.


    Sent from my iPhone using Tapatalk
  21. Tungaloy E20S SCLCR09 D220 Coolant Thru Carbide...

    Tungaloy E20S SCLCR09 D220 Coolant Thru Carbide Shank boring bar, tip appears to need to be built up a bit, 7" OAL $35 shipped

    263578263579
  22. 263575263576263577 Pictures

    263575263576263577
    Pictures
  23. Misc Tooling - BT30 Collet Chucks, Endmills, die files, etc

    Yukiwa BT30-NDC20-75
    new old stock
    Takes Yukiwa YCC20 collets
    $25 ea + ship or 5/$100 shipped

    Die Files, $35 shipped
    Most appear to be Grobet
    A couple have rust and need to be cleaned
  24. Well then...that picture blows. There is a...

    Well then...that picture blows.

    There is a small amount of rust stain (most of it wipes away with my fingers) on the shank...it is visible in the picture.

    Paypal only, and you have to know how...
  25. Fs: 3/4 hss double endmills, Lot of 10, $35 shipped

    263564

    I have a couple/few lots. These are resharps.


    Sent from my iPhone using Tapatalk
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4