Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: upm2019

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    544

    This calculation becomes super crucial for puller...

    This calculation becomes super crucial for puller set ups. If you run too many cycles, the last bit of material will become lodged in the puller then mashed repeatedly into your collet. Could be...
  2. Replies
    7
    Views
    414

    That’s for boring and recessing on a hand screw

    That’s for boring and recessing on a hand screw
  3. Replies
    14
    Views
    544

    I have three Omniturn’s and we use lipe bar feeds...

    I have three Omniturn’s and we use lipe bar feeds . They were 12 feet long but we cut them down to just over six feet to help with the bar whipping and improve finish . We also made an extension for...
  4. The ram is rotated 90 degrees turn it and you...

    The ram is rotated 90 degrees turn it and you should be fine . When I had one the only draw back was if the cutter grabbed it would tip the head up . We had a plug we used .It might be worth the...
  5. They look a bit like Omniturn tool holders Pete

    They look a bit like Omniturn tool holders
    Pete
  6. Replies
    26
    Views
    23,621

    I have had good luck with triumph tools made in...

    I have had good luck with triumph tools made in usa and work good
  7. Replies
    73
    Views
    3,061

    you should look at equipto if I remember you can...

    you should look at equipto if I remember you can get your 12 feet across with posts on the ends. Then a couple along the 32 foot length . Since it’s modular you can configure any way that suits you ....
  8. Replies
    2
    Views
    344

    We put the base outside until we can bust it up...

    We put the base outside until we can bust it up and dump it . Some guy came by and asked if he could have it . I guess he thought it was cast iron I told him he could take it he wanted me to put it...
  9. Replies
    21
    Views
    772

    When I post from my tablet my pics always come...

    When I post from my tablet my pics always come out sideways how do you rotate them
  10. Replies
    7
    Views
    9,426

    I have on I bought at auction 10 years ago . It...

    I have on I bought at auction 10 years ago . It came with a radius attachment which I used once that seemed too cumbersome to learn to use the machine it self is great . You should really use...
  11. I started setting up those things great for its...

    I started setting up those things great for its time . I just saw a few of these at auction a week or two ago they also had the #1 and #2 . They went pretty cheap if you keep your eyes open you can...
  12. Replies
    51
    Views
    9,966

    Before WW2 a lot of Mfg like Brown and Sharpe and...

    Before WW2 a lot of Mfg like Brown and Sharpe and Singer sewing machine made all there fasteners different enough that you couldn’t use off the shelf parts 1/2-12 threads Or odd pitch diameters like...
  13. Replies
    23
    Views
    6,509

    I agree you should call the customer . I was told...

    I agree you should call the customer . I was told when I started out that the only stupid question is the one you didn't ask . Beside's that a call to the customer takes a lot less time then posting...
  14. Replies
    2
    Views
    344

    Parting out Hardinge Conquest 42 SP

    I am parting out a Hardinge Conquest 42 SP with a Fanuc O-T control . I bought the machine at auction and there is a problem with the high res spindle encoder every works with the exception of the C...
  15. Replies
    8
    Views
    1,104

    tag team idiots is what the op and freind are

    tag team idiots is what the op and freind are
  16. Replies
    47
    Views
    2,669

    Sideways photos

    301999
    We have used these chip board boxes they are pretty inexpensive to have made and you can squeeze quite a few on a standard shelf ours are 4x3x12 . Put your parts in and just mark the box #in...
  17. Replies
    54
    Views
    5,054

    That’s an automatic chucker it is a PIA you have...

    That’s an automatic chucker it is a PIA you have to set trip dogs and switch’s then because the feeds are hydraulic you have to constantly adjust them as the machine warms up . They were great...
  18. Replies
    74
    Views
    3,965

    I bought most of my tools years ago when...

    I bought most of my tools years ago when craftsman was good most all of my tools are american made . It is getting harder to find any usa in the stores you have to order online or catoluge . Knpex ix...
  19. I have a couple of customers that will ask for...

    I have a couple of customers that will ask for parts that I have not run in over 10 years so for them I save them . When they call for 5 or 10 or what ever that is the price I work up for them . They...
  20. When we quote we put quantity variance + 5% so we...

    When we quote we put quantity variance + 5% so we can ship any xtra parts we may have . Never discount some customers will figure it out and start to ask for them and expect a discount . Better to...
  21. Replies
    6
    Views
    503

    Thanks for your reply but that doesn’t work I...

    Thanks for your reply but that doesn’t work I have a BND42T5 and it works like yours I have been talking to Miyano and they are waiting to hear from Japan I have to check a couple of switches...
  22. Replies
    44
    Views
    3,211

    If you guys want to work for scrap that’s fine...

    If you guys want to work for scrap that’s fine with me . I came up with a lot of screw machine guys that did just that . You run your ass off all day for scrap to make the difference . What happens...
  23. Replies
    44
    Views
    3,211

    We used to make tens of thousands of parts for...

    We used to make tens of thousands of parts for T&B then one day in the eighties someone thought it would be a great idea to consolidate vendors .A lot of guys got hurt we never had a quality issue or...
  24. Replies
    6
    Views
    503

    300911300911300912300912300910 this is the drive...

    300911300911300912300912300910 this is the drive and motor I think the parts have it as same motor as X axis the line diagram references a valve but there is not one . It also shows a b axis that...
  25. Replies
    11
    Views
    792

    I agree It is very easy to machine but brittle no...

    I agree It is very easy to machine but brittle no problem as long as you allow fow facing back end don't be scared just carefull.
    Good luck
    Pete
Results 1 to 25 of 59
Page 1 of 3 1 2 3