Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: PeterH48

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    380

    Axleson Veet Radial Drill questions

    Looking at a used Veet Radial Drill, anyone ever run one or know anything about them. I searched and a few posts came up about them. Most say it's not a bad machine. Was wondering what morse taper...
  2. Wanted: Radial Drill or HD Drill Press with power feed

    Looking for a cheap Radial Drill Press or a Heavy Duty Drill press with power feed. Prefer machine location within 150 mi of Rhode Island.
  3. Replies
    1
    Views
    351

    Archive section of board

    Does anyone know if there is an archive section of this site where you can view old the old posts?
  4. Need manual for Boyer Schultz 618-H Surface Grinder

    Looking for a manual for my Boyer Schultz surface grinder. Mine is a 618-H, not to be confused with an H618 which is a different machine. There is a Boyer&Shultz manual here on the site, but the link...
  5. Lubrication question on Boyer Schultz surface grinder

    I just picked up a Boyer Schultz 618-H surface grinder. It's almost impossible to find a manual for this machine. It is 1968 vintage. It has the fully hydraulic feed system on the table. Does anyone...
  6. Replies
    2
    Views
    551

    Thanks for the reply. I have been looking at pics...

    Thanks for the reply. I have been looking at pics of B/S surface grinders for the past week and some of the 618 models had a direct drive spindle and the older styles like mine are v belt driven off...
  7. Boyer Schultz surface grinder help needed

    I have a post on the Antique Machinery board, but a member suggested I try here as he said the machine is not considered an antique yet. I have a Boyer Schultz model 618H with a serial number of...
  8. Replies
    2
    Views
    551

    Boyer Schiltz Manual Needed

    I recently picked up a Boyer Schultz surface grinder and I am in desperate need of a manual for it. I cannot find one anywhere, at least not for the model I have. Mine is a 618-H. Serial Number...
  9. Replies
    2
    Views
    1,097

    Machine is sold.

    Machine is sold.
  10. Replies
    2
    Views
    1,097

    Small Racine Power Hack Saw.........CHEAP

    Offering a Racine power hacksaw. Has a 1-1/4 X 14 inch blade. Will cut 5 1/2 inches round, 7 inch wide stock. Runs on a 1/2 HP single phase motor. Comes with 6 extra blades that are sharp and were...
  11. Replies
    4
    Views
    513

    Thanks guys! I know I can always count on this...

    Thanks guys! I know I can always count on this place to find answers for my questions.
  12. Replies
    4
    Views
    513

    Kalamazoo Horizontal band saw question

    I have the very common Kalamazoo Model H9AW horizontal band saw. They use a small wire wheel to keep the cutting chips off the blade. Is that wire wheel supposed to spin on the bracket that holds it...
  13. Replies
    11
    Views
    807

    Keith, is your email working at this site? I...

    Keith, is your email working at this site? I sent you an email message.
  14. Update: I am all set with my part. Secondly, I...

    Update: I am all set with my part. Secondly, I regret now I even mentioned that I am a retired veteran. I will never ever do it again for all of the negativity that it stirred up in this post. I...
  15. project at hand

    For those interested, the part I am working on is a home made adapter for mounting a 42 inch flat belt pulley to a large flywheel on an antique engine. I did not make the adapter. It came with the...
  16. Thank you ripperj. I am in no hurry. Email me...

    Thank you ripperj. I am in no hurry. Email me when you get back from your trip.
  17. Anynone in Rhode Island or nearby Mass/CT interested in helping out a retired veteran

    I am looking for someone with a minimum 15 inch lathe with a spindle capable of taking a 2 inch piece of round stock. I have a 15 minute job that I need help with. My 13 inch lathe is too small....
  18. Replies
    5
    Views
    583

    Anyone??? No one has ever pushed the buttons on...

    Anyone??? No one has ever pushed the buttons on an old Heidenhain DRO?
  19. Replies
    5
    Views
    583

    Mine is not really that big. Here is a link to...

    Mine is not really that big. Here is a link to one just like I have.

    Heidenhain digital readout | eBay

    Mine is a Pos-E-Touch II
  20. Replies
    5
    Views
    583

    Help with Heidenhain Pos-E-Touch DRO

    I have a Bridgeport J head that came with an old Heidenhain Pos-E-Touch digital readout. It is a 2 axis unit which controls the X and Y axis. I cannot get the Y axis to zero out. When I turn it on,...
  21. Great News !!

    I have some great news to report. When I bought the Clausing lathe, the guy I bought it from gave me two heavy duty boxes full of tooling. He was vacating a small shop at an Airport. He said that not...
  22. Clausing 13x36 Round Head Lathe Headstock Question

    I have a 13 INCH Clausing round head lathe and I have a question about the headstock spindle taper. The manual I found online says the machine comes with a #3 Morse Taper. The parts manual shows a...
  23. Replies
    2
    Views
    662

    WTB Large flatbelt pulley

    Looking for a large steel flat belt pulley. 40 inch diameter or larger. Spoked type, or a solid steel center. Contact me if you have something. No paper pulleys please. Thanks
  24. Replies
    31
    Views
    2,519

    Ratbldr427 is correct. The bearings do have lock...

    Ratbldr427 is correct. The bearings do have lock collars. I already chucked one of them in my lathe, but I don't have a carbide tipped boring bar. Maybe I will look into that. The shaft is definitely...
  25. Replies
    31
    Views
    2,519

    I think I will just take the suggestion and mark...

    I think I will just take the suggestion and mark it with some blue dykem and then hand file it.
Results 1 to 25 of 66
Page 1 of 3 1 2 3