Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: gbent

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    8
    Views
    523

    Some sellers put an extra digit in the price. A...

    Some sellers put an extra digit in the price. A few sellers put in two extra digits. This seller thinks his machine is so special there are three extra digits in the price.
  2. The machine is in awful pretty country. Take a...

    The machine is in awful pretty country. Take a few more days and spend some time, not a forced march. If I wasn't booked solid for the next couple of months I'd consider it myself.
  3. Replies
    6
    Views
    626

    I have Erickson QC30 tooling. It will work in...

    I have Erickson QC30 tooling. It will work in any standard 30 NMTB spindle with a drawbar, and also works with Erickson QC30 spindles using the taper end retaining nut. I have both a Series 1...
  4. Look up indexable boring cartridge. Lots of...

    Look up indexable boring cartridge. Lots of flavors.
  5. I have used Fastenal several times, always with a...

    I have used Fastenal several times, always with a good outcome. Items have all been robust so no damage, but the packaging has always arrived in good condition as well.
  6. Shim the top of the fixed jaw between the hard...

    Shim the top of the fixed jaw between the hard jaw and the vise itself as necessary.

    Then you have to make up your mind what you want to do with your facing cut. If you want the piece square to...
  7. What is the shank size? I have done similar...

    What is the shank size? I have done similar holding the shank in a drill chuck in the tailstock and bringing the jaws of the 4 jaw in one at a time until they just touch the part. The drill chuck...
  8. Replies
    4
    Views
    703

    Not to many sub-arc users in this crowd.

    Not to many sub-arc users in this crowd.
  9. Replies
    28
    Views
    1,709

    Fuel drain if the float sticks.

    Fuel drain if the float sticks.
  10. Replies
    18
    Views
    2,002

    I've got a used spindle and new bearings for a...

    I've got a used spindle and new bearings for a 15".
  11. Replies
    24
    Views
    1,878

    I've got the filler if you have the hands and...

    I've got the filler if you have the hands and eyes.
  12. Replies
    22
    Views
    2,053

    In your original post you have driving/driven. I...

    In your original post you have driving/driven. I said its driven/driving, and used a ring and pinion to illustrate your rear axle ratio example.

    In any case, its easy to get words so similar...
  13. Thanks everyone. Indeed, it just needed to have...

    Thanks everyone. Indeed, it just needed to have the board's re-installed.

    Now the problem is the Yaskawa vfd spindle drive shows a ground fault after it's been powered up for a few minutes to a...
  14. Replies
    22
    Views
    2,053

    I disagree, it is driven over driver. In your...

    I disagree, it is driven over driver. In your example, a rear end has a large ring gear (driven), and a small pinion (driver). So say you have 4.11's, 37 teeth on the ring divided by 9 teeth on the...
  15. Replies
    3
    Views
    774

    LeBlond is still in business.

    LeBlond is still in business.
  16. Replies
    22
    Views
    1,598

    I brought my 8' x 75 ton Promecam home on a...

    I brought my 8' x 75 ton Promecam home on a 14,000# bumper hitch. Single tire tandem axle trailer and 3/4 ton pickup. I only had 160 miles, but 1600 miles wouldn't have been a problem. It was...
  17. I think this is quoting Sami "Cash flow is...

    I think this is quoting Sami "Cash flow is vanity, profit is sanity".

    My own thought on looking at your numbers is you have to quit renting out the upstairs to the brothel.



    That is going...
  18. Tree 250/Acramatic 2100 reading disc error, don't have disc

    I just acquired a Tree 250 with a Acramatic 2100 control. I bought the machine as running, unable to test, but no ability to return. After I get it wired up, I get a reading disc error. I didn't...
  19. Replies
    13
    Views
    1,872

    You are correct. The smaller (#5 and down) sizes...

    You are correct. The smaller (#5 and down) sizes have 40 count dials for angle cutters, and 50 count dials for 90° mount cutters. The #7 and #10 cutters are 20 tpi, and have 80 count dials for...
  20. Replies
    109
    Views
    5,924

    You need to get that bugger killed asap. A...

    You need to get that bugger killed asap. A cousin has over $6,000 in repairs to a Ford van (3 instances) from squirrel damage.
    Rodents Are Feasting On Newer Cars' Soy-Based Wiring Insulation - The...
  21. Replies
    15
    Views
    1,126

    If you have enough water in your hydraulic oil to...

    If you have enough water in your hydraulic oil to need a stainless spool you have bigger problems than you have mentioned.
  22. Replies
    13
    Views
    1,872

    DeVlieg bars use 53.1 degrees. Makes a 3-4-5...

    DeVlieg bars use 53.1 degrees. Makes a 3-4-5 triangle.
  23. US taper pins are 1/4" per foot, or 1 in 48....

    US taper pins are 1/4" per foot, or 1 in 48. Metric are 1 in 50.
  24. Replies
    28
    Views
    2,845

    You are asking a lot of money for something that...

    You are asking a lot of money for something that fits the definition of a "white elephant". You are going to have to apply your very best salesmanship skills. That means lots of pictures, including...
  25. Replies
    25
    Views
    1,970

    I don't see why you can't chase the threads with...

    I don't see why you can't chase the threads with a tap in a cordless hand drill. Choose a taper tap if you are worried about initial alignment. The rigidity of a mag drill is much more likely to...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4