Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: TDegenhart

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    10
    Views
    469

    I use the paper trick, then ease the wheel down...

    I use the paper trick, then ease the wheel down until I scratch layout or magic marker. Tom
  2. We called them pecker pins. So add two more...

    We called them pecker pins. So add two more pins.

    Tom
  3. Replies
    5,185
    Views
    783,601

    I'll bite, what is banda_precision? Tom

    I'll bite, what is banda_precision?

    Tom
  4. Replies
    17
    Views
    747

    Bigger catch basin and a oil filter and...

    Bigger catch basin and a oil filter and recirculate system. Bast of both worlds.

    Tom
  5. Not a mold builder, but what strikes me as a...

    Not a mold builder, but what strikes me as a solution is a pancake cylinder of the same diameter as the lock cylinder positioned to be in alignment with the opposite lock cylinder. Put the cylinders...
  6. If you want accuracy use a sine plate. Tom

    If you want accuracy use a sine plate.

    Tom
  7. Replies
    11
    Views
    1,168

    As a customer I wouldn't care what the media...

    As a customer I wouldn't care what the media looks like, I would want to know what the finished part would be like.

    Tom
  8. Replies
    18
    Views
    1,920

    I thought the monsters were the ones where the...

    I thought the monsters were the ones where the operator rode in a carriage attached to the saddle.

    Tom
  9. By no means. You would just have to have a logic...

    By no means. You would just have to have a logic controller that senses voltage and phase angle of the generated leg, that as conditions change, be able to switch in and out balancing capacitors and...
  10. Your not married with kids are you? Tom

    Your not married with kids are you?

    Tom
  11. What do you need a fuel pump for? Gravity feed....

    What do you need a fuel pump for? Gravity feed.

    Tom
  12. Replies
    19
    Views
    1,148

    I concede to 29.6.1 for POWER wire and yes, the...

    I concede to 29.6.1 for POWER wire and yes, the opening statement was about 8 and 10 ga. I was thinking about the control wire. The next point is for field wiring (customer) connectors. Here the...
  13. I agree with kk, from your description, its one...

    I agree with kk, from your description, its one rust spot chasing another. Heating will not clean out the rust. In this case you probably will need to cut away all the rust and replace with good...
  14. Replies
    19
    Views
    1,148

    I don't believe U/L has anything to say in this...

    I don't believe U/L has anything to say in this area. They go by temperature tests. The old JIC standards did require a minimum of 14 ga, but that is the only one I am aware of. I don't think I...
  15. Replies
    1
    Views
    210

    Connect it to 240 and see how it operates. Check...

    Connect it to 240 and see how it operates. Check the motor current.

    Tom
  16. Out of curiosity, how does the classic solid...

    Out of curiosity, how does the classic solid base/jaw Bridgeport vise work?

    Tom
  17. Replies
    30
    Views
    2,208

    Quite honestly, I have never seen a motor fail...

    Quite honestly, I have never seen a motor fail from loose laminations, or for that matter loose windings. For a motor to be U/L listed for class H or other high temperature insulation systems, not...
  18. A solution to this problem I have found is that...

    A solution to this problem I have found is that the stationary jaw is more rigid than the moving or can be made so. Register the work against the stationary jaw and vice bed, then place something...
  19. Replies
    25
    Views
    1,530

    What you find objectionable about TL-1? Tom

    What you find objectionable about TL-1?

    Tom
  20. Replies
    19
    Views
    1,148

    By automatic ferruling machine, is this one the...

    By automatic ferruling machine, is this one the cuts, strips the insulation and assembles the ferrule? Is there room for two ferrules in a saddle clamp termination? Ring and spade terminates are...
  21. Replies
    19
    Views
    1,148

    First to look for, are the ferrules U/L or equal...

    First to look for, are the ferrules U/L or equal listed or recognized? So long as the ferrule is properly assembled per the instructions, it should be just fine. The only advantage that I see is...
  22. Replies
    25
    Views
    1,530

    How does a lathe chuck fit into the Samchully...

    How does a lathe chuck fit into the Samchully company. Best I can determine they are an energy company. Is this a part of an acquisition that will be spun off?

    Tom
  23. Replies
    109
    Views
    5,924

    Part of that is that the more they invade our...

    Part of that is that the more they invade our domain, the more action we take. Flies, mice, rats and such bring diseases and, in the case of mice and rats, destruction. Squirrels less so, with...
  24. Not at all. The wattage will go down with the...

    Not at all. The wattage will go down with the decrease in voltage.

    Tom
  25. Replies
    109
    Views
    5,924

    I have watched some videos on rat killing with an...

    I have watched some videos on rat killing with an air rifle that had some spectacular results on youtube. One was labeled "Rubbish dump Ratting - They're everywhere!", another "Budget night vision...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4