Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: MGKELLY

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    508

    Wells Index 40 parts available

    Hi I have a Wells Index 40 that I'm interested in selling.
    when i bought the mill it had a Bridgeport 2J head which I'm going to keep so only the base is available.
    it's old and I've used it for...
  2. Thanks Les, My particular Boyar Schultz 612...

    Thanks Les,

    My particular Boyar Schultz 612 didn't come with a one shot system, just the oil spout.
    I'll post some picks when i get a chance.

    Joe
  3. Thank you, ironsmith69 I bought the surface...

    Thank you, ironsmith69
    I bought the surface grinder a couple months ago and started cleaning it up.
    I would assume this machine was lightly used or well maintained?

    Joe
  4. Thank You, Michiganbuck I appreciate the quick...

    Thank You, Michiganbuck
    I appreciate the quick response!
    Joe
  5. I know this thread is old, but looking for an...

    I know this thread is old, but looking for an opinion on the table ways on my Boyar Schultz.
    are they original, good/bad shape? thanks, Joe
    252354
    252355
    252356
  6. Replies
    11
    Views
    913

    Stuart, i will test this once the motor is hooked...

    Stuart, i will test this once the motor is hooked up, but a quick question. The 3 wires for the drum switch would connect to the logical bus on port #6, #8, and #11 with #8 jumpered to #7 and #11...
  7. Replies
    11
    Views
    913

    Stuart thanks so much for your help!! I'm...

    Stuart thanks so much for your help!!

    I'm using a 2 pole breaker wired for 220 from panel to the VFD, use the same breaker for my 2J head and just bought another for the Boyar-Schultz.
    The manual...
  8. Replies
    11
    Views
    913

    Thanks Stuart, Ok on the buss bar should i use...

    Thanks Stuart, Ok on the buss bar should i use one of the ports in the diagram, start and stop are the obvious ones but probable not correct?
    Also can i power the VFD off via the breaker when not is...
  9. Replies
    11
    Views
    913

    Hi Stuart, I created a diagram of how the motor...

    Hi Stuart, I created a diagram of how the motor and switch are currently connected. The magnet chuck, light, and dust collector motor are on different 110 lines.
    I'm still confused, do i need cut...
  10. Replies
    11
    Views
    913

    Boyar Schultz 612 to VFD

    Hello, can i connect the VFD and use the ON/OFF switch on the Boyar Schultz or do i need to have the VFD connected directly to the motor and use the VFD to turn it on and off? the motor is a 3/4 HP,...
  11. Replies
    6
    Views
    1,823

    2 of : 6203-2RS Bearing 17x40x12 Si3N4 Ceramic...

    2 of : 6203-2RS Bearing 17x40x12 Si3N4 Ceramic Sealed ABEC-5 Bearings
    2 of : 6908-2RS Ceramic Si3N4 ABEC 7 Sealed Ball Bearing 40x62x12
    1 of : 7007C P5 ABEC-5 Quality High Precision Angular...
  12. Replies
    6
    Views
    1,823

    TTT thanks

    TTT thanks
  13. Replies
    6
    Views
    1,823

    Bridgeport bearing?

    Hello, I’m not a machinist by trade and looking for specs for bearings to rebuild my 2J head.

    For example: Radial/Deep Groove Ball Bearing - Round Bore, 35 mm ID, 72 mm OD, 17 mm Width, Double...
  14. Replies
    4
    Views
    1,119

    The prices are what limit me from buying new,...

    The prices are what limit me from buying new, wish I could. In the long run after the time spent driving to find something probably better off. But for now just looking for something in reasonably...
  15. Replies
    4
    Views
    1,119

    WTB - surface grinder in NJ

    Hello, I'm looking for a surface grinder. Been looking for a 6 x 12 on Craigslist but nothing yet. Really not particular about the make but like the more compact like Boyar Schultz, harig, Reid, ko...
  16. Any other suggestions, I cleaned up the hub down...

    Any other suggestions, I cleaned up the hub down to bare metal and don't see a taper pin?

    thanks, Joe
  17. I checked today and did not see a taper pin. ...

    I checked today and did not see a taper pin. I'll clean it up a little more and recheck.

    thanks, Joe
  18. wells Index 40 - removing crank handle from knee

    Hello, does anyone know how to remove the knee crank handle on a Wells Index model 40 - sorry about the poor pictures - thanks, Joe
    990329903199030
Results 1 to 18 of 18