Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: cmike

Page 1 of 29 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: CMike

    by cmike
    Replies
    3
    Views
    557

    The feed box

    The feed box
  2. Thread: CMike

    by cmike
    Replies
    3
    Views
    557

    I will have to male a call to fine out..I think...

    I will have to male a call to fine out..I think its the feed box.
  3. Replies
    39
    Views
    3,488

    Some bevel gears are made as a match set. Look...

    Some bevel gears are made as a match set. Look for marks on the edge of the gears and see if there is two punch marks on one set and one punch mark on the other. not sure of yours will have them....
  4. Replies
    39
    Views
    3,488

    Not really, Long run time, heat, wreck, who knows.

    Not really, Long run time, heat, wreck, who knows.
  5. Replies
    39
    Views
    3,488

    Yes, take the nut off and inspect the bearings...

    Yes, take the nut off and inspect the bearings for bad track marks. This gears have broken on other machines.
  6. Replies
    39
    Views
    3,488

    Yes, take the nut off and inspect the bearings...

    Yes, take the nut off and inspect the bearings for bad track marks.
    Set the bearings at .002 cold. ( end play back and forth ) Make sure the gear on the motor has a good woodruff key, no roll...
  7. Replies
    39
    Views
    3,488

    Not the motor its self. can you run the motor off...

    Not the motor its self. can you run the motor off the machine ? Then take the fan off the motor and run it, and see the difference. If that is it, you probably can buy a fan. It will be plastic now...
  8. Replies
    14
    Views
    1,243

    I may have one. I have to fine it.

    I may have one. I have to fine it.
  9. Thread: CMike

    by cmike
    Replies
    3
    Views
    557

    CMike

    Looking for a 40 tooth gear for a Milwaukee feed box for sale.
  10. Replies
    14
    Views
    1,243

    ITS A 1C Contourmaster Model LM Year 1966 ...

    ITS A 1C Contourmaster Model LM Year 1966

    The Acratrace number

    CYA IS THE MACHINE TYPE
    5SCOONTOURING RATE
    10-24 DEPTH OF FEED RATE


    Page 17 in the mqnual
  11. Replies
    14
    Views
    1,243

    cmike

    268542 268543



    Do you have a serial number. Not sure if you have the 1 or 1C.
  12. Replies
    14
    Views
    1,243

    I will try to get one to show you today.

    I will try to get one to show you today.
  13. Replies
    14
    Views
    1,243

    I have the manuals. I won't be home until Sunday....

    I have the manuals. I won't be home until Sunday.

    Regards
  14. Replies
    14
    Views
    1,243

    Can you take a picture of the tracer.I can adjust...

    Can you take a picture of the tracer.I can adjust all of the 5 different tracer. You have to time out the slides.
  15. Replies
    9
    Views
    1,176

    The handle near your guide bar need to be correct...

    The handle near your guide bar need to be correct to fit into the slot on the feeds left and right in the roof of the inside of the knee. If you don't you will break off the end of the left and...
  16. Replies
    13
    Views
    807

    Do you have a picture of the head ?

    Do you have a picture of the head ?
  17. Replies
    10
    Views
    1,148

    There are several Vertical head vercipowers for...

    There are several Vertical head vercipowers for sale on the market. I would get that one instead of the horizontal with vertical head Lot stronger for vertical use. When looking at vercipower, check...
  18. Replies
    10
    Views
    1,148

    If you need tooling. Just sign up for the on line...

    If you need tooling. Just sign up for the on line bidding at actions. Lots of companies going under.
  19. Replies
    9
    Views
    1,176

    cmike

    267534 You have a 1966 425 - 20 vertical vercipower. No, that is why you can't get the front bracket out. Do you have a manual ?

    Pull plug 110 and 102. Take the tapered screws out of the ends of...
  20. Replies
    10
    Views
    1,148

    I know the vercipower mill well. They will take a...

    I know the vercipower mill well. They will take a large cut.Get a serial number.
  21. Replies
    9
    Views
    1,176

    You need to take the 2 small plugs out of the...

    You need to take the 2 small plugs out of the front bracket, crake it back in and take the pressure off the llnkage. they are called spider locks. ( small tapered screws in the ends shifting rods )....
  22. Replies
    9
    Views
    1,176

    cmike

    I am on the road. check your private messages
  23. Replies
    9
    Views
    1,176

    Check your private nessages.

    Check your private nessages.
  24. Replies
    2
    Views
    948

    I think that is a English made machine. Check...

    I think that is a English made machine. Check your drive on the pump and see if it's broken.
  25. Here are the years each attachments. 1944...

    Here are the years each attachments.

    1944 Manual Pub. No. M1375 - 1ea Spiral Milling Attachment, stamped on the housing is AEA1P1/35
    Manual Pub. No. M - 2459 1ea (new old stock)...
Results 1 to 25 of 705
Page 1 of 29 1 2 3 4