Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    2
    Views
    210

    Here you can downlpad a manual for the WF3S...

    Here you can downlpad a manual for the WF3S manual and the electrical diagram for the WF2S WF3S WF2SA and WF3SA versiopns
    The WF3S is identical to the WF2S only a bit bigger
    I did have several...
  2. Oke You have a 0.001 accurate crimp die Now...

    Oke
    You have a 0.001 accurate crimp die
    Now you need a 0.001mm accurate cable 0.001mm accurate terminal with a 0.001mm accurate galvanic coating
    And then you have to do it all in a climate...
  3. But we have cheaper transport :stirthepot:

    But we have cheaper transport :stirthepot:
  4. Looked it up The student 1800 is direct drive...

    Looked it up
    The student 1800 is direct drive So no mecanical or electrical clutch

    The brake needs a powersupply
    Or you put a brakeresistor on the VFD and let that do the braking
    It should...
  5. I would stick with the VFD If you reinstall the...

    I would stick with the VFD
    If you reinstall the clutch and brake the motor will see little start stop cycles
    Then the slow starting is not a problem
    But on a VFD you can adjust this slow start...
  6. Is It regulation greed incompetence unwilling to...

    Is It regulation greed incompetence unwilling to cooperate??? I do not know
    But hearing prices for shipping on this forum in the US it must be some of them
    In Europe prices are half or less as...
  7. Replies
    18
    Views
    1,653

    And propane is much much cheaper to use Peter

    And propane is much much cheaper to use
    Peter
  8. Ixion is no longer Look for Maxion instead ...

    Ixion is no longer
    Look for Maxion instead

    Peter
  9. Black knob on the left is the quill lock yes So...

    Black knob on the left is the quill lock yes
    So you could do some milling with it I suppose

    Peter
  10. It does not have the downfeed handle with...

    It does not have the downfeed handle with wormwheel (If someone has one laying around......)
    So not suited for milling
    Jig drilling machine I call it

    Peter
  11. Yes I am from the Netherlands We ship worldwide...

    Yes I am from the Netherlands We ship worldwide though

    Pic for the machine just for fun

    325113 325114

    Peter
  12. I have a nice Fehlmann But its far away and...

    I have a nice Fehlmann But its far away and probbably to expencive
    Peter
  13. Replies
    43
    Views
    2,186

    You are feighting a needless battle Just put...

    You are feighting a needless battle
    Just put him on ignore Life is too short to fight them all
    If you looked at some of his earlier posts you see it is not a personal thing He does it all the...
  14. Ask him why a new design is in place And if he is...

    Ask him why a new design is in place And if he is aware of the financial consequence
    Simple

    Peter
  15. It all starts with the material Ask your...

    It all starts with the material
    Ask your material supplier for a material with tighter tolerances on thickness and good consistant formability
    and quality. They are out there

    Peter
  16. Replies
    43
    Views
    2,186

    Peter from Holland

    Peter from Holland
  17. BTW Do not expext that the powerfeed stops at 0 ...

    BTW Do not expext that the powerfeed stops at 0 It goes a bit further
    In my case of the slotting machine it does not matter that much as the tolerances on depth of a keyway is very generous
    I...
  18. Oke Let me take a shot Ther forkhard only can...

    Oke
    Let me take a shot
    Ther forkhard only can span about 1cm or so in one position So you have to adjust the jaws for every diameter of your workpiece
    To do so you open the jaws until you see a...
  19. Replies
    7
    Views
    622

    I do not think so Better replace the whole angle...

    I do not think so Better replace the whole angle head Or the quill maybe Although you may end up adjusting the bore/quill fit These can be found used A shaft is harder or even impossible to find...
  20. Replies
    43
    Views
    2,186

    ulquiorra Thermite is a bit of the forums nut ...

    ulquiorra
    Thermite is a bit of the forums nut Every site needs one and he earned his tittle
    Put him on ignore or smile for his colorfull language And even sometimes he has something...
  21. Any DRO for EDM has this feature But others...

    Any DRO for EDM has this feature
    But others also
    You can program it to switch a potential free contact at any number on your DRO So also at 0

    I put these on slotting machines where the...
  22. Replies
    43
    Views
    2,186

    Don`t try Thats old shakesperian englisch he is...

    Don`t try
    Thats old shakesperian englisch he is babbling

    Peter


    BTW I cannot help you with your chinese VFD
  23. Replies
    5
    Views
    509

    size seems to be 42-15-13mm A good replacement...

    size seems to be 42-15-13mm A good replacement would be 2pc of 7302 universal matched bearings in the tolerance and preload you want

    Peter
  24. Replies
    14
    Views
    1,301

    When I clicked on those links I got this message ...

    When I clicked on those links I got this message



    Why ???? :angry: :angry:

    Peter
  25. Replies
    15
    Views
    1,433

    You should take off only the angle head Not the...

    You should take off only the angle head Not the complete head The part with the bevel gears So these 2 gears you think are to blame are still in mesh
    Those bevel gears tend to be noisy Esspecialy...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4