Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Jarrod

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    1,437

    Dear Mark, LMAO! I still need to get a...

    Dear Mark,

    LMAO!

    I still need to get a refractometer and was debating about a mixing head, but I'm only mixing in the pail volume, not barrel volume.
  2. Replies
    9
    Views
    1,437

    This feels a bit like a chicken and egg debate......

    This feels a bit like a chicken and egg debate...

    First and foremost there is the question of chemistry... hard water, soft water, DI water, Distilled water... initial concentration and how well...
  3. Replies
    13
    Views
    1,169

    Not a bad idea at all. I looked at those filter...

    Not a bad idea at all. I looked at those filter socks as they came up in another post, but I'm not sure I have the space to make them work well.
    The grinder is a G. Brand machine, which has an...
  4. Replies
    13
    Views
    1,169

    Thanks for the insight, Mark. I'm surprised even...

    Thanks for the insight, Mark. I'm surprised even a 5 micron filter isn't perfect. What grit of wheel are you running?
  5. Replies
    13
    Views
    1,169

    Is this a premade pleated filter or literally...

    Is this a premade pleated filter or literally just sheets of filter paper in some arrangement? Any idea what size particle they're rated for?
  6. Replies
    13
    Views
    1,169

    Not a bad idea either, but I was actually...

    Not a bad idea either, but I was actually planning to fins a fine metal screen as the top level pre-filter.
  7. Replies
    13
    Views
    1,169

    Surface Grinder Coolant Filtration

    First off, I want to thank everyone who has contributed to this topic to date. There is a lot of great info on here... just wish people used more accurate post titles, to improve searches for...
  8. Replies
    1
    Views
    589

    Turns out it's two snap rings, but you need to...

    Turns out it's two snap rings, but you need to take the pump cover off to reach the one on the end of the shaft. May even have to removed the pulley, to removed the pump cover... what a b!#$h!
  9. Replies
    1
    Views
    589

    Cazeneuve HB 500 Transmission Removal

    Motor is pooched, need to take it for a rewind...
    I know the shaft ends are both splined, but I haven't been successful in removing the transmission or brake units from the motor chassis.

    Has...
  10. Replies
    25
    Views
    2,124

    Does that mean the casting is cementite?

    Does that mean the casting is cementite?
  11. Replies
    25
    Views
    2,124

    Maybe not annealing as the annealing temperatures...

    Maybe not annealing as the annealing temperatures are typically much higher. Tempering is done at significantly lower temperatures to relieve stress and lower hardness, which subsequently increases...
  12. Thanks General. It does indeed have belts from...

    Thanks General.

    It does indeed have belts from the AC servo motor to the spindle. I was told there is no rigid tapping, perhaps that is why?
    Do you have the same machine?
    I am just getting...
  13. Replies
    25
    Views
    2,124

    Just a thought... not as familiar with HT CI, but...

    Just a thought... not as familiar with HT CI, but can you temper them back down to spec so you don't have to struggle with the machining?
  14. Fanuc 11M Control - Torque Limitation Command Applied

    Reading through the manual for our Fanuc AC Spindle Servo unit, being used with our Fanuc 11M controller, on a MOri Seiki MV35/40 VMC, there are two conditions occurring on our machine, which both...
  15. Thanks again for all tye details. Any...

    Thanks again for all tye details.

    Any suggestion of age with a serial number: 59-18856?
  16. Thread: Bridgeport Mill

    by Jarrod
    Replies
    99
    Views
    7,207

    How much they asking? with tooling?

    How much they asking? with tooling?
  17. Thanks Larry. The machine actually came with a...

    Thanks Larry.
    The machine actually came with a few of those parts.
  18. That's crazy!

    That's crazy!
  19. Hi Stephen, It does in fact have a t-slot on...

    Hi Stephen,

    It does in fact have a t-slot on the rear of the bed. What does the chasing assembly look like?

    J.
  20. That's sounds like the story of my life and where...

    That's sounds like the story of my life and where all these tools and machines came from!
  21. Ahhhhhh. Thanks Jim, Larry. I knew I could...

    Ahhhhhh. Thanks Jim, Larry. I knew I could count on both of you to fill in the blanks.

    I still have the complete and functional collet closer assembly, but what you're saying makes more sense. ...
  22. Updated to Windows 10 and now I can't add photos,...

    Updated to Windows 10 and now I can't add photos, go figure. Hopefully this link will work:

    ESM-59 Spindle - Google Drive
  23. Identify/Help: ESM-59 Strange Spindle Features

    Hi all. I figure I should ask before I take a hammer to it...

    I'm throwing around the idea of replacing the spindle entirely with a custom spindle to accept 2J collets. I have a pile of 2J...
  24. Replies
    8
    Views
    3,811

    The System is a 3D System Viper 2i... something...

    The System is a 3D System Viper 2i... something or other... the polymer is Clearvu
  25. Replies
    8
    Views
    3,811

    I had that thought exactly. Put a pile in, out of...

    I had that thought exactly. Put a pile in, out of the way.

    The service tech came to have a look. Turned out the laser's are water cooled and the reservoir was low, causing the laser to derate the...
Results 1 to 25 of 185
Page 1 of 8 1 2 3 4