Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Booze Daily

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Do you have macro programming option?

    Do you have macro programming option?
  2. Replies
    27
    Views
    1,171

    Ox, no it doesn’t know if it didn’t push far...

    Ox, no it doesn’t know if it didn’t push far enough. It’s on an encoder and just keeps pushing until it reaches the encoder count to signal the end of the bar.
  3. Replies
    27
    Views
    1,171

    Hey DanASM, I have an EcoLoad that I bought brand...

    Hey DanASM, I have an EcoLoad that I bought brand new in '00. I have the manual in case you need anything on that end.
  4. Replies
    11
    Views
    1,399

    I touch off the tip and program a -Z depth.

    I touch off the tip and program a -Z depth.
  5. I have Haas mills not lathes, but, you can unlock...

    I have Haas mills not lathes, but, you can unlock the parameters by changing Setting 7
    and typing "debug" on the alarm page. Then page around on the Parameter page to see if you can find some...
  6. Do you program a G50 in your programs? There...

    Do you program a G50 in your programs? There maybe be a leftover G50 S950 in memory.
  7. Replies
    10
    Views
    872

    ^^^. I’ve broached small blind key ways with mine...

    ^^^. I’ve broached small blind key ways with mine too. No problems.
  8. Replies
    30
    Views
    1,699

    Also depends on how the CMM guy aligned the...

    Also depends on how the CMM guy aligned the datums.
    An angular slice thru a circle is an oval
  9. Optical comparator

    Optical comparator
  10. Replies
    10
    Views
    830

    I generally don't like to use a facemill unless...

    I generally don't like to use a facemill unless the part is wide enough to get 2 inserts in the cut at a time.
    Otherwise you're just banging one insert thru at a time.
  11. Replies
    10
    Views
    872

    Pretty sure the mill spindle runs off a belt and...

    Pretty sure the mill spindle runs off a belt and encoder.
    Mine has some slop. Don’t know about the lathe, would assume the same.
  12. Replies
    9
    Views
    734

    Yeah. The feed (or rapid, don't remember) jog...

    Yeah. The feed (or rapid, don't remember) jog mode should work. Feed it close, then switch to .0001.

    PITA but that's what it is.
  13. Replies
    9
    Views
    734

    I ran a Maho like that. You could only move the...

    I ran a Maho like that. You could only move the table with the MPG in .0001 mode.
    Have you tried that?
  14. Replies
    34
    Views
    2,981

    Sorry, don’t see an impact in that picture.

    Sorry, don’t see an impact in that picture.
  15. What about braided steel line?

    What about braided steel line?
  16. Could you re-use what's already on there? If...

    Could you re-use what's already on there?

    If not, Amazon.com: Inline Tube (L-3-8) 5' Stainless Steel Spring Wrap/Rock Guard Compatible with 3/16" Brake Line or Tube : Automotive
  17. Replies
    22
    Views
    1,558

    I would pick the one where the girls are cuter.

    I would pick the one where the girls are cuter.
  18. Replies
    36
    Views
    3,349

    Do you think this is better than running just two...

    Do you think this is better than running just two or three with a shorter cycle time? Just curious, I have this internal conflict regularly with our bigger qty runs on our vf5s.[/QUOTE]

    Short...
  19. Replies
    22
    Views
    1,914

    10-24 is the stupidest thread ever invented. ...

    10-24 is the stupidest thread ever invented.
    I’ve had problems tapping titanium and I ended up thread milling.
  20. Replies
    19
    Views
    2,187

    Sounds like you're not activating your cutoff...

    Sounds like you're not activating your cutoff tool offset before setting G54 with it.
  21. Replies
    19
    Views
    2,187

    Could be. Everyone has their own preference.

    Could be. Everyone has their own preference.
  22. Replies
    19
    Views
    2,187

    Program it both ways and compare the code. I've...

    Program it both ways and compare the code. I've never programmed a lathe with CAM, but IME wear IN CONTROL vs IN COMPUTER only has to do with TNR comp (G41 / G42) not tool offset.
  23. You could also buff them off with a hard gray...

    You could also buff them off with a hard gray wheel on a pedestal grinder.
    For the one against the shoulder you may have to undercut the gray wheel so you only get what you want without messing up...
  24. If you have a rotary table and a BP you could nod...

    If you have a rotary table and a BP you could nod the head and crank the turntable to mill your taper using a standard endmill.
  25. Not sure how removing less matl takes less time?

    Not sure how removing less matl takes less time?
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4