Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: LccJester

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    562

    DFE2-4 Dust Collector | Donaldson Torit...

    DFE2-4 Dust Collector | Donaldson Torit By the way this is the dust system we used for just one cnc mill. We had much larger ones for the other machines but we machines contaminated graphite on one...
  2. Replies
    6
    Views
    562

    It will get every where even with a real good...

    It will get every where even with a real good dust collection system. One of the biggest problems is when it mixes with grease it turns in to a paste that can lock up bearings. So be diligent on...
  3. Replies
    103
    Views
    23,651

    does anyone else have the 884 board with EIA/ISO...

    does anyone else have the 884 board with EIA/ISO chip set? Benganboll hasn't sent me any thing yet and it doesn't look like he has been on here in over two months. I hope everything is alright with...
  4. Mobil DTE extra heavy would be the close...

    Mobil DTE extra heavy would be the close equivalent it is 150 turbine oil
  5. Thread: Whoops...

    by LccJester
    Replies
    1
    Views
    868

    not sure on the cost to repair or replace the...

    not sure on the cost to repair or replace the door but as far as was that a crash the answer is absolutely yes. Any time you make a mistake that causes damage it's a crash, but on the other hand a...
  6. Replies
    5
    Views
    818

    https://www.deumol.com I was able to find the...

    https://www.deumol.com
    I was able to find the correct cables from this site for a reasonable price compared to others. Hope this helps the next person looking for them.
  7. Replies
    12
    Views
    1,093

    We have a Dainichi flat bed turret lathe that has...

    We have a Dainichi flat bed turret lathe that has been in service here for 25 years and it has been a great machine. We have had some guys over the years that let's just say they were a little rough...
  8. Replies
    2
    Views
    683

    This problem was resolved with replacing the BL 2...

    This problem was resolved with replacing the BL 2 D100 servo drive
  9. Replies
    2
    Views
    683

    Update I have found a cable that was plugged in...

    Update I have found a cable that was plugged in to the wrong socket. Now that it is plugged in to the correct socket I am getting 923-13 alarm. If I unplug cable I get the 919-13 alarm back. Which...
  10. Replies
    2
    Views
    683

    Okuma 919-13 alarm help

    we have an Okuma Impact LU35 twin turret lathe with An OSP7000L controller we are trying to bring back online. When we start it up we get alarm 919-13 Z axis encoder alarm. We have swapped out the...
  11. Replies
    26
    Views
    2,300

    ok video makes it clear it's just a display piece

    ok video makes it clear it's just a display piece
  12. Replies
    23
    Views
    2,157

    we have a dry ice blaster here and it works good...

    we have a dry ice blaster here and it works good for cleaning but it doesn't do good for removing rust or paint. If you turn the pressure up enough to start removing paint and rust it clogs up due to...
  13. Replies
    26
    Views
    2,300

    looking at the scale it shows about 0.500 judging...

    looking at the scale it shows about 0.500 judging by that it doesn't look to be 37" long, but it says it was made by someone so the scale could be off.
  14. Replies
    5
    Views
    818

    The ends are CA7103

    The ends are CA7103
  15. Replies
    5
    Views
    818

    Fiber optic cables

    We’ve got a machine with some bad fiber optic cables on an Okuma with an OSP7000L controller. What I need is a place to buy new replacements with the correct ends to replace them.
  16. Have you had any luck yet?

    Have you had any luck yet?
  17. Replies
    103
    Views
    23,651

    benganboll that would be great and thank you. My...

    benganboll that would be great and thank you. My E-Mail is the same as my user name @gmail.com
  18. Replies
    103
    Views
    23,651

    I have the 884 board does any one have the files...

    I have the 884 board does any one have the files for the four chips I need instead of the six chip set?
  19. Replies
    15
    Views
    1,559

    We used to have 4 Doosan lathes in our shop....

    We used to have 4 Doosan lathes in our shop. (shop was shut down for 5 years previous management screw up) They were great machines and best of all the took a beating from new guys and kept going.
  20. I'm defiantly impressed with this machine...

    I'm defiantly impressed with this machine already. The stuff I have figured out about it so far shows just how far ahead Mazak controls were ahead of Fanuc, but my next project will be waking up an...
  21. Replies
    4
    Views
    1,282

    I hope you are wrong about FC going away cause I...

    I hope you are wrong about FC going away cause I don't think some of our customers would like us using 360 with the cloud base storage. I am curious to try 360 out when I get a chance to mess with it...
  22. thanks a million Gobo that was the ticket I was...

    thanks a million Gobo that was the ticket I was not aware of the spindle direction needing to be set in the tool data. I currently have a love hate relationship with this machine lol. I love what I...
  23. Replies
    103
    Views
    23,651

    cwtoyota thank you for all the help

    cwtoyota thank you for all the help
  24. I had to reinitialize the controller and re...

    I had to reinitialize the controller and re install all the parameters after changing batteries. there were a few other bugs that I have worked out already just stuck on this problem right now. I...
  25. Replies
    4
    Views
    1,282

    Featurecam or Fusion 360

    the company I work at is starting our machine shop back up after a five year hiatus. Long story short we were sold off. when we were running before we had Feature cam and we got it back but it came...
Results 1 to 25 of 26
Page 1 of 2 1 2