Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JohnEvans

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Well that is what my 1986 BP operators & parts...

    Well that is what my 1986 BP operators & parts book states, 2 different part# for left and right! So who knows??
  2. NOPE !! Parts list show different numbers. Left...

    NOPE !! Parts list show different numbers. Left side takes 2 bearings RH only 1 Bearing seat is wider on LH.
  3. The 2 Webb mills depending on condition and...

    The 2 Webb mills depending on condition and tooling included here in Phoenix $4000-6000 each. The Goodway lathe again depending on chucks toolpost and any tooling about the same. The CNC stuff not a...
  4. Replies
    13
    Views
    1,105

    Duhh I think so !! rub equals friction that...

    Duhh I think so !! rub equals friction that equals HEAT !! You may also have a electrical issue but to start fix the rub.
  5. As said earlier the cylinder also serves as the...

    As said earlier the cylinder also serves as the reservoir/tank. That fitting very well maybe a breather besides being the filler port, being it is on the non-pressure side of the cylinder.
  6. Replies
    58
    Views
    4,894

    Google to the rescue Creeper Caster 3 in Use...

    Google to the rescue
    Creeper Caster 3 in Use With 4WM23 PK4
  7. Replies
    58
    Views
    4,894

    I prefer the old style creeper wheels ,the ones...

    I prefer the old style creeper wheels ,the ones that roll on the edge, casters like most modern creepers have suck. I had a gennie Lisle "jeepers creeper" for damm near 50 years till I backed over it...
  8. Replies
    13
    Views
    1,225

    Torch one out from a piece of 1/4-3/8 strap ,a...

    Torch one out from a piece of 1/4-3/8 strap ,a bit of finish work with a 4-1/2 grinder and Bob's your uncle !!
  9. Replies
    9
    Views
    496

    do those oil fill cups have some felt inserts to...

    do those oil fill cups have some felt inserts to meter the oil? If not unless you oil them every few minutes those bearings will be running dry more often than not. That would be a good place for a...
  10. Replies
    6
    Views
    731

    Wood lathe or possibly a metal spinning lathe....

    Wood lathe or possibly a metal spinning lathe. Weird TS who knows?? I'm sure there was some reason for it though.
  11. Replies
    3
    Views
    734

    Machining books

    Set of 8 "Modern Shop Practice" in 4 othersvery good condition plus 4 others [see pictures for titles]
    $80 shipped priority FR Absored all I could out of these so time to pass on to the next reader!...
  12. Replies
    25
    Views
    1,411

    And that's why you DO NOT extend the slide out...

    And that's why you DO NOT extend the slide out beyond the end of the base for general use! But fixable for sure.
  13. Replies
    34
    Views
    7,815

    Well nowadays I don't know how big a OS pistons...

    Well nowadays I don't know how big a OS pistons for that would be available. Back in 70s and earlier I would expected to find .080s from someone like Badger-Silvolite etc. Those flathead Continentals...
  14. Replies
    29
    Views
    2,204

    Well the big question is where this part was made...

    Well the big question is where this part was made ??? If in the USA and more than 20-30 years ago inch thread 99.44% sure. If from over seas metric same % chance. Do not often see metric threads in...
  15. Replies
    34
    Views
    7,815

    Well if you COULD get a reply with the block...

    Well if you COULD get a reply with the block casting # which would be F600AXXX that would tell you that it was the right 6 cyl series. What is the bore on your old engine you know? Your old engine...
  16. Replies
    34
    Views
    7,815

    You do know that the F209-F226 series engines are...

    You do know that the F209-F226 series engines are the same size outside dimension wise ? The usual biggest difference between forklift engines and the rest is most forklift engines have 5 gear front...
  17. Being that is a duel voltage motor it IS wired...

    Being that is a duel voltage motor it IS wired for the voltage you are using? I would think a 1/2 HP capacitor start and run motor would be the correct one for that lathe. As I said earlier SB's flat...
  18. The question IS what motor is on there now ?...

    The question IS what motor is on there now ? Would be very unlikely your current motor has either brushes or magnets. 1hp motor is a bit big as SB's are limited by the flat belt for power...
  19. Gee ,Looks more like a planer to me !!

    Gee ,Looks more like a planer to me !!
  20. The zerks one the end of the table on the BP...

    The zerks one the end of the table on the BP looks like grease on them. Big NO NO !!
  21. There is no such thing as a repair manual for any...

    There is no such thing as a repair manual for any Grizzly product . Grizzly bought the South Bend NAME only that is the ONLY relationship there. The only "timing" involved is when you engage the half...
  22. Replies
    2
    Views
    526

    Try this on for size !! And no comments about my...

    Try this on for size !! And no comments about my shaky writing ! LOL
  23. Replies
    14
    Views
    5,338

    good luck with that ,OP has not been on the forum...

    good luck with that ,OP has not been on the forum in about 2-1/2 years.
  24. Well the portable boring bar unless it has ALL of...

    Well the portable boring bar unless it has ALL of it's tooling is worth very little ,they do make a good floor lamp bases however.
    As said to rebuild modern engines it takes much more...
  25. Good luck with that price,Be suprized if you even...

    Good luck with that price,Be suprized if you even get a bid.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4