Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: poyo

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    So, most of the problems are solved. I could not...

    So, most of the problems are solved. I could not clean it as thorough as I wanted but don't have time to go any deeper.

    Any suggestions on how to push the wicks through oil channels? Also, to y...
  2. Replies
    5
    Views
    721

    Here you go, if you need any other dimensions...

    Here you go, if you need any other dimensions feel free to ask, I am taking my machine apart currently so everything is everywhere :willy_nilly:

    330128
  3. Replies
    5
    Views
    721

    I'll be away from home till Thursday next week,...

    I'll be away from home till Thursday next week, once I am home I'll make a sketch and send it to your way.
  4. Replies
    5
    Views
    721

    328794 Is this the nut you need the dimensions...

    328794

    Is this the nut you need the dimensions of?
  5. Replies
    8
    Views
    9,136

    There is a Czech site where most of the...

    There is a Czech site where most of the Czechoslovak machine manuals can be found

    Manualy a navody k obraběcim strojům | TumliKOVO:Technologie strojniho obraběni kovů
  6. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Correction, it is m18x1 and I could not find off...

    Correction, it is m18x1 and I could not find off the shelf item with that specs, they have 17x1 and next size is 20x1. I made like 4 of them, in case similar size is used elsewhere on the machine.
  7. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    No, I did not actually. I wanted to manufacture...

    No, I did not actually. I wanted to manufacture them because I am really bad at cutting threads on the lathe and looking for excuses to practice.

    PS. Just checked out of curiosity, it costs around...
  8. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    So, I finally received the bearing and 56 teeth...

    So, I finally received the bearing and 56 teeth mod1 spur gears I needed for the lathe to be able to make the missing nut. Usually the case... From (almost) compete set of change gears only ones I...
  9. Replies
    6
    Views
    937

    Bruce can have them if he agrees to share the...

    Bruce can have them if he agrees to share the content with me 😜😜😜
  10. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Shaft has some room to move back and forth if you...

    Shaft has some room to move back and forth if you don't have the front nut so the #7 post from me has a photo where it is pushed back, and the gear was hold in place by the contact of the gear within...
  11. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Viola! It is out :) 326484 326485 I gave...

    Viola! It is out :)

    326484 326485

    I gave it a quick blow with the hot air gun on the highest setting, then used the wooden wedges, came out after couple of hits.

    326487326486

    what seems...
  12. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    My initial idea was to use some putty on the 3d...

    My initial idea was to use some putty on the 3d printed part to give some mechanical strength to it and paint with oil resistant 2k pur. My concern was that if oil gets hot. But I believe it won't...
  13. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Also finished the design and printing of splash...

    Also finished the design and printing of splash guard,I'll do a test fit, if its alright, will be sent for casting.

    325853
    325854325855
  14. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Wedge idea sounds safer but I doubt there is...

    Wedge idea sounds safer but I doubt there is enough space between the casting and the gear ti push them, but I'll still give it a try, I have lots of oak cutoffs laying around. I'll also check how...
  15. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    You mean something like on brake rotor of the...

    You mean something like on brake rotor of the cars I believe?, if it comes to that I think I'll follow as you suggested.
  16. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Tnx for the manual Erik, I have the same scan...

    Tnx for the manual Erik, I have the same scan probaby was also from you or I found it somewhere in the forum.

    There was some surface rust on the ways but the rest seemed fine, most of the sealed...
  17. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    I found the section cut from the manual from 1938...

    I found the section cut from the manual from 1938 and it matches the design of my machine so yea machine was produced around that era.

    325825

    I have to back to workshop to make better photos of...
  18. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Indeed It'll be more amazing once I am done...

    Indeed


    It'll be more amazing once I am done with it hopefully :D
  19. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Still having troubles getting the bevel gear out,...

    Still having troubles getting the bevel gear out, without the nut in place I thought it will just slide off.. Any idea?
  20. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Hello Dave, great thnx for the code. I'll see if...

    Hello Dave, great thnx for the code. I'll see if I can use it. Though my lathe is metric, so once I got the missing gears(56t was the only one I was missing) should be okay






    Yea mine...
  21. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Also, yesterday I decided to make the missing...

    Also, yesterday I decided to make the missing nut, then realized I don't have 56T gears in my set, and those are the ones I need for 1mm pitch... So I ended up ordering raw Mod1 56T gears that I have...
  22. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Hello Alan, thank for the info, I started from...

    Hello Alan,

    thank for the info, I started from the top and I will see what else is waiting for me on my quest. Machine is from 1936-38 so pretty old and had seen many owners I'd believe. The two...
  23. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    325593 its not a very complex part to produce,...

    325593
    its not a very complex part to produce, worse case I'll turn it from a round stock and weld two tapped pieces for screwing it in place.

    another question, at the end of the bar there is a...
  24. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    Tried that also, waiting for the response :)

    Tried that also, waiting for the response :)
  25. Thread: FP 1 Dismantle

    by poyo
    Replies
    44
    Views
    3,621

    No, grease was used only inside the vertical...

    No, grease was used only inside the vertical head, the rest was oiled(which has turned into a slimy substance). I already contacted to Franz and price was a bit too spicy for my taste :) I can...
Results 1 to 25 of 45
Page 1 of 2 1 2