Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: HWElecRepair

Page 1 of 35 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    267

    5/16-18 Jon

    5/16-18

    Jon
  2. Replies
    6
    Views
    461

    Take the D200 apart, remove the printed flex...

    Take the D200 apart, remove the printed flex cable from the connector on the PCB and clean both the cable and connector with alcohol. Put it back together and you have about a 90% chance that your...
  3. Replies
    1
    Views
    393

    Bridgeport Size Differences

    This really has no importance, but we thought it was fun.

    We discovered today that an M head quill housing will literally fit inside of a Series II quill housing.

    321556
    321557
    321558

    And...
  4. Sadly it hasnt been this way for a long time, at...

    Sadly it hasnt been this way for a long time, at least for the last 8 years. Its either mill brackets or lathe brackets.

    Jon
  5. Replies
    1
    Views
    215

    When you say you hooked up another monitor, do...

    When you say you hooked up another monitor, do you mean that you hooked the monitor directly into the motherboard? If so, I would go with a bad motherboard. Can you post a picture of the...
  6. I prefer Acu-Rite. Accurate, good quality, easy...

    I prefer Acu-Rite. Accurate, good quality, easy to install.

    If you are worried about contamination, I would go with a Magnascale or Mitutoyo next. With Newall's move to Mexico, they have had...
  7. Replies
    5
    Views
    311

    Jerry went into business for himself and even...

    Jerry went into business for himself and even sometimes gets on here. His number is 716-490-1462.

    If he cant hook you up, he might point you to Don Schoof. 313-640-8080

    Jon
  8. Replies
    13
    Views
    783

    Oh, no I dont have a schematic of that. The...

    Oh, no I dont have a schematic of that. The circuit boards have gone through a few rev's through the years, but I have done some base component R&R on them.
  9. Replies
    13
    Views
    783

    A schematic or a parts diagram? I dont have a...

    A schematic or a parts diagram? I dont have a schematic, but the parts breakdown has a rudimentary wiring diagram in it.

    What exactly are you looking for?

    Jon
  10. Replies
    2
    Views
    262

    Is your lube properly functioning and getting to...

    Is your lube properly functioning and getting to all of the ways?

    Jon
  11. Replies
    13
    Views
    783

    Also, when you have the brushes out, check for...

    Also, when you have the brushes out, check for continuity between the metal of the brush holder and ground. Sometimes they will come from the factory with the set screw overtorqued and it cracks the...
  12. Replies
    13
    Views
    783

    Are either of your brush holders kinda loose? ...

    Are either of your brush holders kinda loose?

    Jon
  13. Replies
    7
    Views
    591

    Not really. I have seen a bunch in garages and...

    Not really. I have seen a bunch in garages and barns that make them easier to move around because of the limited space in a smaller shop.

    Jon
  14. Replies
    13
    Views
    783

    Pots rarely go bad on these, I have probably only...

    Pots rarely go bad on these, I have probably only changed out 5 or so for the pot actually being bad. Sluggish or no response to feed pot movement is normally something with the motor, whether it...
  15. Replies
    5
    Views
    450

    Some of those cables are going to have to be...

    Some of those cables are going to have to be made. Post a picture of the inside of your cabinet and I will let you know.

    Jon
  16. Replies
    5
    Views
    450

    No. The scale signal is basically shutoff when...

    No. The scale signal is basically shutoff when the motor is running in 3 axis mode.

    Jon
  17. Replies
    5
    Views
    450

    Most Trak's utilize a rotary encoder and use the...

    Most Trak's utilize a rotary encoder and use the scale for when the ballscrew is disengaged. The cantilever style typically ran off only a scale.
  18. Replies
    7
    Views
    591

    We make leveling feet bars and go through them...

    We make leveling feet bars and go through them like hot cakes. I know there are a few different bases for Series 1's (Man, JR would have jumped all over me for that one) but to my knowledge, the...
  19. Barry said he believe that grinding the spindle...

    Barry said he believe that grinding the spindle would correct the issue. He also says that a spindle should not be ground in relation to the bearings, but ground on its own.

    +1 to everyone (it...
  20. The only aftermarket power feed that comes with...

    The only aftermarket power feed that comes with all the necessary stuff that I have seen is a Servo. The biggest issue with what you have is that your leadscrew actually ends underneath the table. ...
  21. Replies
    2
    Views
    344

    It would be easier to know what scale you have...

    It would be easier to know what scale you have and what you are trying to accomplish. The round 6 pin connector and the ENC/SENC-150 scales both used a 5V TTL signal. However, the Mate scales used...
  22. Can you post the pics here? Are you already sold...

    Can you post the pics here? Are you already sold on wanting the machine and asking us to back up your want to buy it? To be upfront, I am always hesitant when people ask what a machine is worth or...
  23. Replies
    2
    Views
    404

    That is really gonna make people not want to help...

    That is really gonna make people not want to help you out, just an FYI.

    The easy answer is "sure" that is where the serial number is, on the front of the knee. However, we have come across some...
  24. The bracket is the same, the length of the screws...

    The bracket is the same, the length of the screws are what seperates them. I have like 2 pair left.

    Jon
  25. Replies
    28
    Views
    1,533

    +1 to this.

    +1 to this.
Results 1 to 25 of 854
Page 1 of 35 1 2 3 4