Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: saadracing

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    276

    Drip feed. OSP700 controller

    Drip feed. OSP700 controller
  2. Replies
    3
    Views
    276

    DNC program for 1998 Okuma

    Any recommendations for a DNC program for RS232? We have Fusion360 but having an issue getting any response for this from my rep. I see a few options but wanted to see if there was any...
  3. Replies
    0
    Views
    543

    1998 Okuma Cadet Mate 4th axis wiring

    Wanted to see if anyone wired in a 4th axis on a cadet mate that was not prewired for it from the factory.
  4. Replies
    12
    Views
    1,024

    Yeah. They are all working. There was a program...

    Yeah. They are all working. There was a program left in the machine and ran it. Green and orange lights are working perfect. So the wiring diagram above is right. Thank for all the help. Hope this...
  5. Replies
    12
    Views
    1,024

    Today, i was getting ready to diag. the lights...

    Today, i was getting ready to diag. the lights and I had the air hose disconnected. Powered the machine on and the red light lit. I noticed that when I went from auto mode to manual mode the light...
  6. Replies
    12
    Views
    1,024

    Soooo, no luck. I did not get a red light when...

    Soooo, no luck. I did not get a red light when powering on. I should as i get an alarm for magazine not in basic position (air pressure loss) Looks like I should see 24v on wire 300. Do you have a...
  7. Replies
    12
    Views
    1,024

    Ok, so after digging around I found the diagram...

    Ok, so after digging around I found the diagram on Schniders web site (link below) On page 5 it has the wiring diagram which confirms that wire 300 goes to lug 0
    ...
  8. Replies
    12
    Views
    1,024

    Spots 4 and 5 do not go anywhere. They go up the...

    Spots 4 and 5 do not go anywhere. They go up the light tower to nothing so it would be the same as not connecting it at all. As if you were going to add 2 more lights on top.

    After looking at the...
  9. Replies
    12
    Views
    1,024

    Here are the photos. The wires are labeled the...

    Here are the photos. The wires are labeled the same as the diagram and connected to the tower as stated above

    259415
    259416
  10. Replies
    12
    Views
    1,024

    Okay 1= green = H12 = 800 2 = orange = H13 =...

    Okay
    1= green = H12 = 800
    2 = orange = H13 = 804
    3 = red = H11 = 802

    300??? There is nothing attached to lug #4 and #5. They look as thought you could add 2 additional lights to the tower.
    ...
  11. Replies
    12
    Views
    1,024

    I can reverse engineer those with my multi-meter...

    I can reverse engineer those with my multi-meter except wire 300. The diagram show wire 300 to have continuity to H11 12 and 13 but none of the lugs have continuity and neither do the wires
  12. Replies
    12
    Views
    1,024

    Okay, so I have the same cable diagram but not...

    Okay, so I have the same cable diagram but not the wiring schematic. The wires on the machine are as labeled in the diagrams.

    The issue is on the tower base I have 6 lugs and they are labeled 1...
  13. Replies
    12
    Views
    1,024

    1998 Okuma Cadet Mate 4020 Light tower

    Does anyone happen to have a picture of or the wiring diagram for the light tower? The riggers removed it for transport and the manual does not have the diagram, only the cable information. The label...
  14. Replies
    6
    Views
    633

    Yes. The technician said that was the best he...

    Yes. The technician said that was the best he could get
  15. Replies
    6
    Views
    633

    Okuma Cadet mate 4020 Z backlash

    Looking at purchasing an older 1998 Okuma Cadet mate 4020 and running some test on it showed a 0.0004" backlash in the Z axis. As soon as we get to the 0.0004" (moving in 0.0001" steps)on the control...
  16. Replies
    15
    Views
    1,263

    Thanks for the info

    Thanks for the info
  17. Replies
    15
    Views
    1,263

    I understand that it is not simple nor did I mean...

    I understand that it is not simple nor did I mean to imply. Was trying to gain some new knowledge in the process as this is not a part of high precision.
  18. Replies
    15
    Views
    1,263

    We are doing just a few parts. If it works as I...

    We are doing just a few parts. If it works as I thinks is should we will look into larger runs and have them done at an actual molder. HDPE is what we have available at the shop. Thanks for the...
  19. Replies
    15
    Views
    1,263

    Will just be using our hand hydraulic press. Says...

    Will just be using our hand hydraulic press. Says 20 ton but actual is probably around 10 to 15 ton
  20. Replies
    15
    Views
    1,263

    Cold slug? Not familiar with this. The mold...

    Cold slug? Not familiar with this. The mold should be fairly air tight as all of the mating surfaces will be lapped on a stone and then bolted together
  21. Replies
    15
    Views
    1,263

    Injection mold question

    I am making a mold to inject HDPE. The final product is just a flat rectangle sheet of plastic with a smaller rectangle on top of it by 0.250" thick. I am making a aluminum cylinder to melt the...
  22. Has anyone used these tailstock turrets? Opinions?

    Looking at these from Enco and wanted to see if anyone had any feedback on how well these work/precision/durability.

    Thanks

    Buy Tailstock Turrets from UseEnco
  23. Yes please!

    Yes please!
  24. We are having them centerless ground to the...

    We are having them centerless ground to the specified diameters and then we do the finishing opts so unfortunately not an option. Thanks though
  25. With the required clamp load needed to hold the...

    With the required clamp load needed to hold the stud in place and the rotational torque load of the rolling head, i am concerned about damaging the threads. Thoughts?
Results 1 to 25 of 27
Page 1 of 2 1 2