Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: janvanruth

Page 1 of 36 1 2 3 4

Search: Search took 0.01 seconds.

  1. so i could hook up a vfd in the mains going to...

    so i could hook up a vfd in the mains going to the motor and switch between low and high rpm as long as there is a moment of no voltage in between high and low?
    if that is possible i will take it....
  2. as my two eyes need different correction and also...

    as my two eyes need different correction and also a cylindrical correction the cheap ones will not work.
    i was planning to get my eyes checked out anyway as i have found out that my center view as...
  3. i started out with cheap cheaters for some time...

    i started out with cheap cheaters for some time before i got to the eye doctor.
    got prescription glasses about +.50 and +.25, intended just for reading.
    it was a world of difference.
    had the half...
  4. thanks for the contributions. as i am putting a...

    thanks for the contributions.
    as i am putting a burnerd multi size chuck on this smaller lathe and i intend to keep it there, i think i will go for the vfd on the high speed.
  5. are a Dahlander 2 speed motor and a vfd compatible?

    i wonder if i could, without problems, connect a vfd to my lathe that has a Dahlander 2speed motor.
    the lathe has a lever on the apron to select the high and low electrical speeds and to get from...
  6. whom are you talking to? nobody used the word "...

    whom are you talking to?
    nobody used the word " epic ".
    nobody was talking about the Maxi Torquerite at $ 500.
  7. drill the last hole,leave the drill in...

    drill the last hole,leave the drill in place,unclamp the piece, move over the table, clamp the piece,continue drilling?
  8. if the threads are deep enough i would first tap...

    if the threads are deep enough i would first tap with the 14 mm a couple of turns into the old thread before reaming it out.
    i think it would improve your chance of picking up the old thread.
    if...
  9. not quite the run of the mill influencer as he...

    not quite the run of the mill influencer as he does not try to sell anything, but he is inspiring.
    YouTube
  10. the living proof that it is the machinist and not...

    the living proof that it is the machinist and not the machine
    YouTube
  11. Replies
    1,291
    Views
    108,804

    ryannair has made public that it will start also...

    ryannair has made public that it will start also flying airbus until the max can be delivered.
    maybe it is just put out there to put pressure on boeing, but they bought lauda and lauda flies airbus....
  12. Replies
    15
    Views
    723

    ditch the vice and clamp it to the bed on a plate...

    ditch the vice and clamp it to the bed on a plate with some locating pins and clamps.
    how long would it take to make a that plate, maybe an hour?
    no matter what kind of drill you will be using, if...
  13. to me those $ 300,000 a year sounds a lot like...

    to me those $ 300,000 a year sounds a lot like profit not revenue.
    one could pay a guy $ 1000 a week to just make the video and edit it and still have $ 250,000 at the end of the year.
  14. you might want to start a new thread just asking...

    you might want to start a new thread just asking about the price and leaving out the intro
  15. Replies
    28
    Views
    1,528

    7.6 mm for a m8x1 mm bolt? i doubt it very...

    7.6 mm for a m8x1 mm bolt?
    i doubt it very much...
  16. no, as nobody here will have that machine, you...

    no, as nobody here will have that machine, you had better ask around on the homeshop machinist forum
  17. a picture would help....

    a picture would help....
  18. always thought that anodising creates a thin...

    always thought that anodising creates a thin layer that is quite a good electrical insulator.
    the tin plating was done galvanically?
  19. chrome plating / anodising of aluminium? aircraft rims possible?

    a customer has some aluminium? rims of an airplane he wants to have a nice shiny surface.
    they are not going on an aircraft ever again, it is just for the looks.
    can they be chrome plated/ anodised...
  20. long term, period

    long term, period
  21. don't know about Lailin but both Kondia and Tos...

    don't know about Lailin but both Kondia and Tos are decent machines.
    i could be mistaking but i believe Kondia was sold in the USA as Lagun.
    if in good working order i would not hesitate on either...
  22. years ago i had trouble with my car idling up and...

    years ago i had trouble with my car idling up and down.
    made an appointment with the dealer for diagnostics.
    drove the car onto the diagnostics stand and the head mechanic came over.
    as he took a...
  23. Replies
    10
    Views
    1,742

    in future before answering to a thread have a...

    in future before answering to a thread have a look at how old it is
  24. plus the #30 has a better direct collet, be it...

    plus the #30 has a better direct collet, be it that they are rare and expensive
  25. sorry but i wouldn't know what they are called in...

    sorry but i wouldn't know what they are called in french
    heraklith makes them
    2.5 cm strong is about 25 euro per square meter in Holland.
Results 1 to 25 of 900
Page 1 of 36 1 2 3 4