Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Phil in Montana

Page 1 of 54 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    210

    First find the 7 ton chain fall, go to the scrap...

    First find the 7 ton chain fall, go to the scrap yard and find the beams, and the hard part the wheels...Phil
  2. You make the best money when the job is a job...

    You make the best money when the job is a job that only your shop can do, and you know it, I always love the cust to say "I hope you can do this for me I have been everywhere" I always reminded the...
  3. Except for one little tiny winy little thing...I...

    Except for one little tiny winy little thing...I sure as hell paid more taxes than you ever did (that have been totally wasted) and now under your pride and joy we will watch inflation destroy what...
  4. standardparts, You are wasting your time,The...

    standardparts, You are wasting your time,The blind will never see...Phil
  5. Ok If you want a real bang up job, get out your...

    Ok If you want a real bang up job, get out your check book and go shopping, no wimpy drive pack... but a full Ward Lenord drive with feedback and instant reversing...And a mg set. and constant...
  6. Why cut them up, there is little profit in...

    Why cut them up, there is little profit in scraping, just load whole and haul...Phil
  7. If it from CNN its doggy dew, everyone knows...

    If it from CNN its doggy dew, everyone knows that...Phil
  8. Replies
    19
    Views
    902

    Why do you want the headache, just leave a little...

    Why do you want the headache, just leave a little flat spot and sand it out...phil
  9. Why reinvent the wheel, get a vfd and a 3phase...

    Why reinvent the wheel, get a vfd and a 3phase motor...Phil
  10. You blame them? I would run too...so much for...

    You blame them? I would run too...so much for 40/hr jobs...burger king here I come...Phil
  11. Did you grawl the arm for a short?...Phil

    Did you grawl the arm for a short?...Phil
  12. Use a lathe and mount the drill in the tool post...

    Use a lathe and mount the drill in the tool post and use power feed...Real easy to make some money...Phil
  13. Replies
    5
    Views
    307

    Dont go there, on a scale of 1-10 its a 1/2, find...

    Dont go there, on a scale of 1-10 its a 1/2, find a 10ee standard engine lathe...Phil
  14. With the inrush amps to start a 3hp 240 volt...

    With the inrush amps to start a 3hp 240 volt motor, I would go for 30 amp plugs, will not cost anymore and will not fail as easy...Phil
  15. Replies
    17
    Views
    876

    Just run the T30 at the lowest speed the chart...

    Just run the T30 at the lowest speed the chart allows... It will be good, a intake filter will help... Mine turns at 400 rpm...Phil
  16. Replies
    2
    Views
    261

    I have never seen one here in the states...Phil

    I have never seen one here in the states...Phil
  17. Replies
    46
    Views
    2,002

    You really think so? add 28% cap gains to this BS...

    You really think so? add 28% cap gains to this BS and see what happens...The DEMS own it...Phil
  18. Replies
    17
    Views
    876

    IR T30, all you need to know, now go buy...

    IR T30, all you need to know, now go buy one...Phil
  19. Replies
    5
    Views
    347

    18000 rpm and you want to do what?...Phil

    18000 rpm and you want to do what?...Phil
  20. Replies
    52
    Views
    3,480

    5 rules for machining magnesium... 1.fire...

    5 rules for machining magnesium...


    1.fire ex for metals
    2. clean the chips as you make them
    3. sharp bits
    4. slow speeds fast feeds, (no little chips)
    5. Never leave the machine
    If you...
  21. I silver braze in a vac, works real well, never...

    I silver braze in a vac, works real well, never tried to arc weld...Phil
  22. The L&S have the loudest gear boxes of the good...

    The L&S have the loudest gear boxes of the good lathes, monarch are the quietest, Only thing I didn't like about a L&S...Phil
  23. Hll I do it with a file...Phil

    Hll I do it with a file...Phil
  24. Replies
    52
    Views
    3,480

    I caught a chip pan on fire once, in a lathe...

    I caught a chip pan on fire once, in a lathe turning to fast, but getting a really nice shiny finish...then a little shooting star. the whole pan went up and white smoke every where, tried to put it...
  25. And right on spec +-.00005 Lots of luck with...

    And right on spec +-.00005 Lots of luck with that...Phil
Results 1 to 25 of 1326
Page 1 of 54 1 2 3 4