Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rustytool

Page 1 of 45 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    471

    I just watched the video. Strange. Maybe try...

    I just watched the video.
    Strange. Maybe try tapping it in with a rubber mallet.
    Make sure you have a rod that you can use to knock it out from the other end.
    Could the end of the collets slot be...
  2. Replies
    4
    Views
    416

    The skid it's on looks pretty nice. Maybe they...

    The skid it's on looks pretty nice.
    Maybe they could actually load it onto a truck without breaking off all the handles.
  3. Replies
    11
    Views
    471

    It's about .700. There should be a key in the...

    It's about .700.
    There should be a key in the spindle that the slot in the collet engages.
    Unless it was sheared off or just removed to gain more through spindle capacity.
  4. Replies
    11
    Views
    471

    Hardinge did make a 6R collet also. Here's one...

    Hardinge did make a 6R collet also.
    Here's one in the foreground compared to the Hardinge 6H.267142
  5. Replies
    11
    Views
    471

    Balas also made a 6H collet with a flat face. I...

    Balas also made a 6H collet with a flat face.
    I believe that Balas made the Rivett collets because some of my Rivett stamped collets are also stamped Balas and they are identical to the only Rivett...
  6. Replies
    11
    Views
    471

    Travis, The collet in the foreground is a 3mt...

    Travis, The collet in the foreground is a 3mt adapter, then a Rivett 6R collet in the middle and then a Hardinge 6H collet at the rear.
    They all have the same taper angle. The 3mt has a straight...
  7. Replies
    31
    Views
    3,529

    A weak point of the K&T I believe is one motor to...

    A weak point of the K&T I believe is one motor to lift the knee and run the spindle.
    Lifting the knee doesn't always go smoothly.
    Can I send you all my handles to have polished ?
    I saw one once...
  8. Replies
    18
    Views
    922

    I had 3 of these 6R to 3MT adapters. I just sold...

    I had 3 of these 6R to 3MT adapters.
    I just sold 2 and have one left.
    The bad news is I'll sell it for $8000.
    The good news is I'll throw in the lathe for free but you have to come pick it up.
  9. Replies
    1
    Views
    423

    Might be a Holland, made in Erie Pennsylvania.

    Might be a Holland, made in Erie Pennsylvania.
  10. Replies
    11
    Views
    1,563

    No steady or follower rest. Another member who...

    No steady or follower rest.
    Another member who isn't really active here anymore has told me that he spoke with Keith Rucker and that Keith has plans to make castings of the steady and follower he...
  11. Replies
    11
    Views
    1,563

    Inch metric is a nice feature to have but even...

    Inch metric is a nice feature to have but even though I wasn't looking for it the new lathe does have inch metric threading. It's a Holbrook C10.
    It won't be here for a few weeks.
  12. Replies
    11
    Views
    1,563

    Sold a Studer OD grinder. I'm getting another...

    Sold a Studer OD grinder.
    I'm getting another 10x20 size lathe that has always been on my bucket list and need the room and funds for it.
    I've experienced the Rivett for 8 years and want to try...
  13. Replies
    11
    Views
    1,563

    I would consider trades for just about anything...

    I would consider trades for just about anything that blows my dress up. Like a Mori Seiki MS 850 or 1250.
    Or a nice metal shaper. OR an ID/OD cylindrical grinder or surface grinder or bandsaw to...
  14. Replies
    11
    Views
    1,563

    Rivett 1020S For Sale

    Before I put it on eBay for a 99 cent starting bid I thought I'd try here first.
    1954 1020S serial number 239.
    Excellent condition. Has done everything I've asked of it and has never let me down in...
  15. That was fun. The easiest way to sell a machine I...

    That was fun. The easiest way to sell a machine I have found yet.
    Think I'll do it with my Rivett.
  16. Congratulations, I sent you a message through...

    Congratulations, I sent you a message through eBay but I'm not sure if they let the phone number through.
    You can call or email.
    Greg. 208-596-7258
    [email protected]
  17. Looking for Vancouver B.C. area member to inspect lathe

    If there is a Vancouver B.C. area member that is going to Lenmark Industries in Langley
    that can inspect a lathe for me call or email. Thanks, Greg.
    208-596-7258
    [email protected]
  18. Replies
    48
    Views
    3,608

    Maybe it's because I live off the beaten...

    Maybe it's because I live off the beaten interstate path but the fastest I ever got anything from McMaster was 2 weeks.
  19. Replies
    19
    Views
    1,934

    Thanks Rich, I figured it would probably be more...

    Thanks Rich, I figured it would probably be more than it's worth.
  20. Replies
    19
    Views
    1,934

    Rich, I have this K&T 2HL Vertical all apart and...

    Rich, I have this K&T 2HL Vertical all apart and cleaned. I keep thinking it would be a shame to put it back together without scraping it.
    How much does something like that cost ?
    Greg.265098
  21. We are off the beaten path. 90 miles to the...

    We are off the beaten path. 90 miles to the nearest interstate.
    In my experience shipping a machine from Ohio is around $2500.
  22. If instead of paying cash on pick up I might be...

    If instead of paying cash on pick up I might be interested in a trade for something of equal value to the winning bid. Since your coming out with a truck and trailer anyway you could haul the...
  23. It's 5'3" wide, 4' deep and 6'3" tall sitting on...

    It's 5'3" wide, 4' deep and 6'3" tall sitting on a nice heavy duty pallet.
    I could use the floor space but in reality I'm just a guy who likes all kinds of interesting machine tools.
    My shop isn't...
  24. I totally realize the time and expense to come...

    I totally realize the time and expense to come pick this up, that's why I started the auction at 99 cents.
    I thought about including free shipping but I'm not totally crazy, yet.
  25. I would guess the weight to be at least 2000,...

    I would guess the weight to be at least 2000, maybe 2500 pounds.
    I would leave the table on. It's not roller ways.
    It's on a heavy duty pallet and can be loaded with a forklift that will cost an...
Results 1 to 25 of 1113
Page 1 of 45 1 2 3 4