Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: ace400xs

Search: Search took 0.00 seconds.

  1. The bore listed on the card is difficult to make...

    The bore listed on the card is difficult to make out but it appears to say 1 1/8". It measures at 1.3".
  2. FS: South Bend 14 1/2" x 6' Lathe (NE Ohio)

    I have a South Bend 14 1/2" x 6' lathe for sale here in north east Ohio. It is currently not wired up but when I purchased it several years ago, I had been cleaned up, painted, and had the motor...
  3. Joe, I received your PM and responded but unsure...

    Joe, I received your PM and responded but unsure if it actually sent it or not as it isn't showing in my sent folder.
  4. This item is sold.

    This item is sold.
  5. FS: Wohlhaupter UPA3 Precision Boring/Facing Head w/R8 Taper

    I have a UPA3 Wohlhaupter Boring/Facing head with R8 taper for sale. I purchased this from a US Navy contractor in New Jersey. I am in the process of getting rid of my Bridgeport mill so this is no...
  6. Replies
    32
    Views
    5,712

    I really appreciate the wealth of knowledge so...

    I really appreciate the wealth of knowledge so far in response to my question. I'm sure as I continue on this journey I will have many more...

    I pick up my Bridgeport this weekend. I had to do...
  7. Replies
    32
    Views
    5,712

    There is a Precision Matthews dealer nearby in...

    There is a Precision Matthews dealer nearby in Pittsburgh that I did stop by back when I first started this search, but at the time I was looking for any pre-owned lathes he might have (he didn't...
  8. Replies
    32
    Views
    5,712

    Definitely a greenhorn here so I will be taking...

    Definitely a greenhorn here so I will be taking it slow and easy. I've pretty much eliminated that larger 18" Boye and Emmes from the equation. While it sounds like it could do fine work in the...
  9. Replies
    32
    Views
    5,712

    That is little outside of the range I have been...

    That is little outside of the range I have been searching on Craigslist, but within easy driving distance. Definitely worth checking out.

    J
  10. Replies
    32
    Views
    5,712

    I guess I thought based on my reading on this...

    I guess I thought based on my reading on this forum and other's that the Logan's were held in higher esteem than they seem to be, at least on this thread.

    The spindle bore and the length are...
  11. Replies
    32
    Views
    5,712

    Looks enticing and not an unrealistic drive. ...

    Looks enticing and not an unrealistic drive. Thanks for the lead.
  12. Replies
    32
    Views
    5,712

    Gears all looked good, no broken teeth, and we...

    Gears all looked good, no broken teeth, and we ran through most of them. What is the easiest way to check the flatness of the bed?

    Oh and I am willing to drive quite a ways for the right deal. ...
  13. Replies
    32
    Views
    5,712

    I got a chuckle out of that too. Perhaps it's...

    I got a chuckle out of that too.

    Perhaps it's the price range that I have been shopping in, but I always end up being a day late when a good deal pops up. Btw, the price on this Logan is well...
  14. Replies
    32
    Views
    5,712

    Looking to buy first lathe - Logan

    I have been lurking around here for a while and finally have a reason to post. I have been shopping for a lathe for sometime for my shop. I just recently added a Bridgeport mill. My ideal lathe...
  15. Replies
    13
    Views
    3,458

    I have decided to pass on the B&E based on advice...

    I have decided to pass on the B&E based on advice I have gotten here and from friends. I have a line on a Sheldon that I hope to make a deal on this weekend. It seems sized more appropriately for...
  16. Thanks for posting these. Nice find. I am in a...

    Thanks for posting these. Nice find. I am in a somewhat similar position as you (minus actually having the machines yet) and have been following this thread and soaking it all in. Lots of great...
  17. Replies
    13
    Views
    3,458

    I wasn't able to make it over there tonight to...

    I wasn't able to make it over there tonight to get any pictures as I got held up at work, but just going from memory, that looks fairly similar to the machine I am looking at. How would you rate the...
  18. Replies
    13
    Views
    3,458

    Thanks for all the advice and anecdotes, it is...

    Thanks for all the advice and anecdotes, it is greatly appreciated. This is definitely not the ideal lathe for me. Although I have the room for it, it definitely takes up more than I would...
  19. Replies
    13
    Views
    3,458

    18" swing, 4' between centers. Takes up about...

    18" swing, 4' between centers. Takes up about 10' x4' of floor space.
  20. Replies
    13
    Views
    3,458

    Looking at Boye and Emmes for first lathe

    So I have been shopping around for a mill and lathe for sometime now. I have been browsing this forum and it has been a great source for information while on this quest.

    I came across this Boye...
Results 1 to 20 of 21