Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: morestainless

Search: Search took 0.00 seconds.

  1. Replies
    35
    Views
    6,560

    As for that excessive slop and locking up, sounds...

    As for that excessive slop and locking up, sounds like one of the two bearing lock nuts came loose and jammed the tapered bearings against each other. Take off the handwheel and dial to get to it.
  2. Replies
    35
    Views
    6,560

    Almost ready to go in its new location. It has...

    Almost ready to go in its new location. It has the 56" table, 72" table slide, and full, 36" table travel. Power table feed would be cool I guess.
  3. Replies
    35
    Views
    6,560

    I'm looking for a universal work head for this...

    I'm looking for a universal work head for this machine. There seem to be a few on eBay. Were there different versions of the universal (early, middle, late) with improvements or are they all...
  4. Replies
    35
    Views
    6,560

    I found this modern art masterpiece under the...

    I found this modern art masterpiece under the paint on the end of the table (non load bearing surface). Dunno if Cincinnati did this or Boeing, when they rebuilt it.
  5. Replies
    35
    Views
    6,560

    Thanks for the offer. I'll keep that in mind.

    Thanks for the offer. I'll keep that in mind.
  6. Replies
    35
    Views
    6,560

    I have a special application so I'm gonna put a...

    I have a special application so I'm gonna put a ball screw/nut/servo on the in-feed and add a reduction wheel/pully/servo on the columns crank shaft. 10ths no problem. No backlash in the column. ...
  7. Replies
    35
    Views
    6,560

    It's a good 8 degree grade up to the landing at...

    It's a good 8 degree grade up to the landing at the back of the house. Gotta have a guide line/brake on the back and pull it across, inch-by-inch. 1-1/2 inch to spare on either side of the ramp. It...
  8. Replies
    35
    Views
    6,560

    You lost me. There's no half nut in the OM. Do...

    You lost me. There's no half nut in the OM. Do you mean saddle lead screw and nut?
  9. Replies
    35
    Views
    6,560

    ...more on this picture. They put this surface...

    ...more on this picture. They put this surface "flaking" on with a hand grinder. I ordered my 5-20-C Tubular Scraper today.
  10. Replies
    35
    Views
    6,560

    After getting the thing completely torn down, I...

    After getting the thing completely torn down, I gotta say, I'm impressed with the build of the "little tank".
  11. Replies
    35
    Views
    6,560

    thanks, I have this one:

    thanks,

    I have this one:
  12. Replies
    35
    Views
    6,560

    No. I don't. Just M-1833.

    No. I don't. Just M-1833.
  13. Replies
    35
    Views
    6,560

    The Boeing scraping/oil pocket job from 1968...?

    The Boeing scraping/oil pocket job from 1968...?
  14. Replies
    35
    Views
    6,560

    The balls roll smoothly over these darkened track...

    The balls roll smoothly over these darkened track spots. Though the owner didn't understand why I insisted on removing the table for transport, the machine had also set for the last 10 years,...
  15. Replies
    35
    Views
    6,560

    0ne year older than me. It has 29 balls in one...

    0ne year older than me.

    It has 29 balls in one bronze ball cage on each track.
  16. Replies
    35
    Views
    6,560

    Made in 1952?

    Made in 1952?
  17. Replies
    35
    Views
    6,560

    Thanks. Ser. 1D2T1Z-202 Says rebuilt by...

    Thanks.

    Ser. 1D2T1Z-202

    Says rebuilt by Boeing 4/23/68.

    Though the table moved smoothly, I can see the track surface and balls are slightly worn (no pitting). I suppose a set of slightly...
  18. Replies
    35
    Views
    6,560

    Cincinnati #2 TCG in my Driveway

    It came up for sale just 1 hr. away, so I had to haul it home. I gave them 2/3 of what they asked. No tooling/fixtures other than centers and the one wheel attached. It is in decent enough shape...
Results 1 to 18 of 18