Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: johnoder

Page 1 of 60 1 2 3 4

Search: Search took 0.16 seconds.

  1. Well...you can always proceed along with taking...

    Well...you can always proceed along with taking cross slide and all on top as an assembly off and SEE what the hold up is
  2. Replies
    5
    Views
    1,338

    You could ask them (Lucas Precision) if they are...

    You could ask them (Lucas Precision) if they are still around, but I seriously doubt they would have much to say with no serial number which has yet to be found.

    The early forty series booklet I...
  3. Replies
    4
    Views
    262

    High class equipment - but only if everything...

    High class equipment - but only if everything (feeds/rapids/speed changes) works perfectly. Its full of hydraulic systems that are getting old. These were new when I was going thru the...
  4. Take off nuts on tee bolts and lift it straight up

    Take off nuts on tee bolts and lift it straight up
  5. Thread: Hendey 14x5

    by johnoder
    Replies
    1
    Views
    181

    Recent thread with info in Post #5 Hendey...

    Recent thread with info in Post #5

    Hendey lathe, Farmington CT

    Made in later teens
  6. Replies
    23
    Views
    903

    Lots of time, patience and "penetrating" type...

    Lots of time, patience and "penetrating" type oil/solvent - with an equal portion of bumping on things to see if any more movement than last week.

    Helped by purposeful set ups so its a no brainer...
  7. Replies
    23
    Views
    903

    Machine was built PRIOR to the separate hardened...

    Machine was built PRIOR to the separate hardened outer vee ways - see his last photo in post #1 and notice that front way has no joint like your hard ways machines have
  8. Replies
    9
    Views
    391

    Spindle nose hardened and ground - like all D...

    Spindle nose hardened and ground - like all D type Monarch spindles. Good luck on cutting on it with any accuracy - unless set up in a suitable ID grinding machine
  9. Manual shows pieces (page seventy-one). If Taper...

    Manual shows pieces (page seventy-one). If Taper Attachment equipped, you have to start at the back - screw goes THRU the sliding block and has a nut on the back you cannot see

    Sliding block is...
  10. Replies
    23
    Views
    903

    This isn't easy but is most satisfying. This...

    This isn't easy but is most satisfying. This machine sat out for years, but the cast iron did not seem to lose any of its beauty

    Illustrates the semi dull way scraper approach to shoving off the...
  11. Replies
    16
    Views
    1,971

    The images at least

    The images at least
  12. I would imagine that additional photos would help...

    I would imagine that additional photos would help in possibly arriving at both identification and disassembly process
  13. Replies
    4
    Views
    400

    No, fairly recent (2009 :D ) purchase on Ebay if ...

    No, fairly recent (2009 :D ) purchase on Ebay if I recall correctly
  14. Replies
    11
    Views
    500

    That's it for oil supply - there isn't any in...

    That's it for oil supply - there isn't any in head stock simply because the head stock has a hole in the rear bottom that matches the top of the sump.

    The two sight glasses tell me the level...
  15. Replies
    7
    Views
    526

    Its a vise. Use it to make some jaws. Not like...

    Its a vise. Use it to make some jaws. Not like you are going to ruin anything on the vise - assuming you don't clamp down on chips or the like.

    A good thing to get used to when you want to own...
  16. Replies
    4
    Views
    400

    With your four vee ways, I'd guess earlier. ...

    With your four vee ways, I'd guess earlier.

    Here is another biggie closed tail 4 vee moldering away out New Mexico way

    Latest patent date Spring 1900
  17. The replacing gears have to have at least enough...

    The replacing gears have to have at least enough members to turn the cam shafts the same direction as the timing belt did

    ALL four stroke cam shafts turn at one half crank shaft speeds - like 20...
  18. :confused: I don't think e stops apply to...

    :confused:

    I don't think e stops apply to clutched lathes like the CY. The clutch lever disengages clutch and applies brake - assuming that did not wear out long ago
  19. Replies
    11
    Views
    500

    Here is how my 20 standard (a raised 16") sump...

    Here is how my 20 standard (a raised 16") sump looked
  20. Replies
    6
    Views
    307

    If 14 x 6 (what ever is cast into face of bed...

    If 14 x 6 (what ever is cast into face of bed casting) it likely has 1 3/16 hole thru spindle

    Four jaw chuck is what you want - it is far easier to learn to center up work in a four jaw than it...
  21. Replies
    11
    Views
    500

    May be the rear sump style? - pump has to pull...

    May be the rear sump style? - pump has to pull the oil up and on to the distribution trays. Sump is low, bolted to bottom of rear head stock casting. Need to be able to SEE oil in its pair of...
  22. Replies
    23
    Views
    903

    Good stuff. Cast iron ways so the rust shoves...

    Good stuff. Cast iron ways so the rust shoves off nicely with a semi dull way scraper or even a razor blade

    Lots of related pubs at Greg Menke's pouncetronics web page - see there Bulletin 16 and...
  23. Replies
    11
    Views
    500

    Would be my guess if not overfill No rubbing...

    Would be my guess if not overfill

    No rubbing seals for sure

    Next time you move it tilt it up and watch the oil run out:D
  24. Probably gray - like the publication ...

    Probably gray - like the publication

    http://www.vintagemachinery.org/pubs/2097/16339.pdf
  25. Replies
    30
    Views
    2,148

    Great to hear Joe - thanks for update. :D

    Great to hear Joe - thanks for update. :D
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4