Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: beeser

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    28
    Views
    2,279

    The seller of the Dorian milling cutter that I...

    The seller of the Dorian milling cutter that I purchased wasn't able to deliver so I'm back to square one. What is the recommended insert for general purpose work on the Iscar tool mentioned? There...
  2. Replies
    28
    Views
    2,279

    My Bridgeport is 2hp. What makes the higher hp...

    My Bridgeport is 2hp. What makes the higher hp more susceptible to vibration?

    Good to know about making heavy cuts with a flycutter. I never thought about damaging the setscrew key.

    I have...
  3. Replies
    28
    Views
    2,279

    Wish I would've paid more attention to your...

    Wish I would've paid more attention to your earlier post, especially the pic where the Iscar milling cutter was clearly identified. I'll look around to see if one of those is available at a...
  4. Replies
    28
    Views
    2,279

    I have and use a flycutter with HSS bits. It...

    I have and use a flycutter with HSS bits. It works great for light and finish cuts but the reason for inquiring about the carbide indexable milling cutters, both shell and the one I purchased is for...
  5. Replies
    28
    Views
    2,279

    As somewhat of a crapshoot and out of frustration...

    As somewhat of a crapshoot and out of frustration I ended up purchasing the following Dorian 2" R8 end mill with some KORLOY GRADE PC5300 inserts. The inserts will probably not do double duty for...
  6. Replies
    4
    Views
    551

    Good point. Using the screws holding the two...

    Good point. Using the screws holding the two halves together, tap them while they are unscrewed and slightly proud of the main body. The ring gear pops out when the halves are separated. I'm a...
  7. Replies
    4
    Views
    551

    Scratch the question. I figured out a way of...

    Scratch the question. I figured out a way of breaking this thing apart.
  8. Replies
    4
    Views
    551

    Buck "Adjust-Tru" Chuck Disassembly?

    I purchased a used Buck "Adjust-Tru" 8" Chuck and while removing the D1-4 mount noticed that it was terribly dirty and corroded between the mount and main body. Seems like it was used a lot with...
  9. Replies
    28
    Views
    2,279

    This looks good but who makes it?

    This looks good but who makes it?
  10. Replies
    28
    Views
    2,279

    Face Mill Recommendation?

    So far I've been satisfied using HSS for tooling but using end mills for facing, which I've been doing a lot lately is frustrating. I would like to get a face mill that uses carbide inserts but...
  11. Replies
    4
    Views
    738

    2nd in line if deal falls through

    2nd in line if deal falls through
  12. Replies
    5
    Views
    1,723

    The set was already sold by the time bob was...

    The set was already sold by the time bob was reached.
  13. Replies
    25
    Views
    2,786

    The only grinding wheels I use for sharpening my...

    The only grinding wheels I use for sharpening my woodturning tools are CBN. I've had members of our machinist group visit my home shop and try out my CBN wheels and ALL have purchased their own...
  14. Replies
    10
    Views
    1,262

    You seem adamant about this. How so?

    You seem adamant about this. How so?
  15. Replies
    10
    Views
    1,262

    The one listed by Bob was already sold. Well, at...

    The one listed by Bob was already sold. Well, at least I know they exist and where to look.
  16. Replies
    10
    Views
    1,262

    Thanks JohnEvans! I just responded to the seller.

    Thanks JohnEvans! I just responded to the seller.
  17. Replies
    5
    Views
    1,723

    I'll take it if it's a D1-4. Steve

    I'll take it if it's a D1-4.
    Steve
  18. Replies
    10
    Views
    1,262

    Jacobs Rubber-Flex Collet Chuck in D1-4?

    A friend of mine has a Jacobs Rubber-Flex Collet Chuck that I thought might be useful to own. Were these made in D1-4? There are plenty of them available online but I haven't found one in D1-4.
  19. Replies
    0
    Views
    386

    Dern Grinding Jig? PIC

    Has anyone used the Dern grinding jig shown below?
    264223
  20. After spending a little time on the Lathe...

    After spending a little time on the Lathe inserts.com site it appears this might be a good place to start. The offerings don't seem as overwhelming as what is available at the big boy sites. ...
  21. Thanks Bob and Jeremy! I should have been...

    Thanks Bob and Jeremy! I should have been clearer in my earlier post. I already have the Aloris tool post and #1, #2, #4D and #7 holders and was looking to enhance the set with the carbide tool...
  22. Suggestions for first carbide tool holders?

    I finally decided to get some carbide tool holders and inserts. Any suggestions on type and brands for an Aloris BXA? I'm just a hobbyist so these would be used for general use. My lathe is a...
  23. Replies
    5
    Views
    861

    The size wire run to the compressor from my 3...

    The size wire run to the compressor from my 3 phase panel is 10 gauge, which is the recommended size in the IR manual. What was throwing me off is the following in the manual under the heading of...
  24. Replies
    5
    Views
    861

    Air compressor circuit breaker size?

    While trying to justify a 40 amp circuit breaker for my 5hp, 3 phase, 240 V air compressor I came across a chart of unknown origin that called for 2x the FLAs of the motor, which is 13.9 according to...
  25. Replies
    27
    Views
    1,968

    Thanks again SAF!! I ended purchasing the 3...

    Thanks again SAF!! I ended purchasing the 3 heaters you mentioned. Odd that I didn't see it myself when looking for them. Everything should be golden now with the proper heaters. I'm in the...
Results 1 to 25 of 238
Page 1 of 10 1 2 3 4