Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: vegard

Search: Search took 0.00 seconds.

  1. Replies
    30
    Views
    1,624

    Ill tap something other than air to check it

    Ill tap something other than air to check it
  2. Replies
    30
    Views
    1,624

    Haha!!! I think itís working. It wanted an s...

    Haha!!! I think itís working. It wanted an s command on the g84.2 line.
  3. Replies
    30
    Views
    1,624

    Vancbiker, my bad... duh.... hereís some more...

    Vancbiker, my bad... duh.... hereís some more screenshots during the...
  4. Replies
    30
    Views
    1,624

    No, they were just taken with the machine doing...

    No, they were just taken with the machine doing nothing. Iíll try to get a look during the tap cycle.
  5. Replies
    30
    Views
    1,624

    F31 is set to 1. Here are some pictures of the...

    F31 is set to 1. Here are some pictures of the ladder both symbol and adress display...
  6. Replies
    30
    Views
    1,624

    Vancbiker, Here is the page. Iíll look into the...

    Vancbiker,
    Here is the page. Iíll look into the spindle drive parameter tomorrow. Thank you for the help!
    https://uploads.tapatalk-cdn.com/20210329/8d20a54842bc9b7caff18451e0895348.jpg
  7. Replies
    30
    Views
    1,624

    Vancbiker, here is a picture from the electrical...

    Vancbiker, here is a picture from the electrical book, does this look like the right...
  8. Replies
    30
    Views
    1,624

    Douglas, everything I see in the manual and...

    Douglas, everything I see in the manual and research says rigid tapping is g84.2 without an m code, but I have tried as you suggested as well without success. Im starting to feel pretty confident...
  9. Replies
    30
    Views
    1,624

    Also, no change to the real x0020 bit 5

    Also, no change to the real x0020 bit 5
  10. Replies
    30
    Views
    1,624

    Parameter 9122 is 0 0 0 1 0 0 0 0 (as shown on...

    Parameter 9122 is 0 0 0 1 0 0 0 0 (as shown on screen)
  11. Replies
    30
    Views
    1,624

    I also checked the parameter settings, and it...

    I also checked the parameter settings, and it matches the book.
  12. Replies
    30
    Views
    1,624

    Ok- I donít have the programming manual, but I do...

    Ok- I donít have the programming manual, but I do have the instruction manual, which is what the pictures are from. I looked through the m and g code lists, and I donít think there is a preparatory...
  13. Replies
    30
    Views
    1,624

    Thanks for the advice so far, I will try all of...

    Thanks for the advice so far, I will try all of the suggestions tomorrow morning. We had to make parts with the machine today. I will say the enshu is a nice smooth machine, my kitamuras of the same...
  14. Replies
    30
    Views
    1,624

    https://uploads.tapatalk-cdn.com/20210225/4c935b5d...

    https://uploads.tapatalk-cdn.com/20210225/4c935b5dd0daa60b2b1bf639df0fdb85.jpghttps://uploads.tapatalk-cdn.com/20210225/c8785224f3ffcbaa8c530a3b0c659d40.jpg
  15. Replies
    30
    Views
    1,624

    Thanks for the replies. DandD I tried your...

    Thanks for the replies. DandD I tried your variations and a few more. It didnít like M29, so I tried M54 also (one of my kitamura wants m54) and I tried with and without spindle on. Slow spindle...
  16. Replies
    30
    Views
    1,624

    Rigid tapping on 15M Enshu

    Hi,
    I recently picked up an Enshu 650vx with Fanuc 15M control.

    I am making parts on the machine, but I havenít figured out how to rigid tap successfully yet. I am starting to think that I may...
Results 1 to 16 of 16