Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jim rozen

Page 1 of 60 1 2 3 4

Search: Search took 0.13 seconds; generated 16 minute(s) ago.

  1. Replies
    24
    Views
    813

    Don't believe everything you read on the...

    Don't believe everything you read on the internet. I think mine was 100 bucks via ebay. Granted
    a motor shop *would* have a megger on hand....
  2. Replies
    24
    Views
    813

    Many DVMs read down to 0.01 ohm resolution. You...

    Many DVMs read down to 0.01 ohm resolution. You need to cancel out the lead resistance with that
    function on the meter (clamp one alligator clip to another when doing this) but it works pretty...
  3. Replies
    24
    Views
    813

    Best approach: Check the resistance of each...

    Best approach: Check the resistance of each winding with a DVM that reads down to 0.01 ohm resolution. They should pretty well match.
    Then check between windings and ground with a DVM that reads...
  4. Replies
    153
    Views
    11,817

    [QUOTE=CarbideBob;3445137]H The OP is not a pro...

    [QUOTE=CarbideBob;3445137]H
    The OP is not a pro rider with a ton of experience

    Excellent point. Rule one: below freezing, take the 4 wheeler. If you are work and conditions
    deteriorate,...
  5. Replies
    153
    Views
    11,817

    [QUOTE=digger doug;3445013][QUOTE=jim...

    [QUOTE=digger doug;3445013][QUOTE=jim rozen;3444963]
    "Aware of the traction Issues" ???
    Driving along at 35f, nice dry road, come over a hill, area shadowed with trees, ice patch.

    That is the...
  6. Replies
    5
    Views
    320

    Fast and "cheap" might be to cut down a HSS MT...

    Fast and "cheap" might be to cut down a HSS MT drill and point the stub?

    Drill shanks like that are usually soft. I'd go with the 'buy 'em from a proper supplier' route.
  7. The stock rest can be bored out to accept a four...

    The stock rest can be bored out to accept a four inch diameter part, including the clearance to put ball bearings on the
    fingers as well.
  8. Replies
    153
    Views
    11,817

    [QUOTE=digger doug;3444589]Yup, nutzo bike rider...

    [QUOTE=digger doug;3444589]Yup, nutzo bike rider hit's ice, slides over to my lane (oncoming)
    and I splatter 'em… not my fault.

    There's a nice twisty road near me, during the summer season it's...
  9. Replies
    268
    Views
    16,577

    "same as the Democraptic party is going about...

    "same as the Democraptic party is going about more slowly, already, and several years in at a slow train-wreck."

    Hmm. You seem to maybe want to emmigrate to someplace else probably. Your own...
  10. Replies
    153
    Views
    11,817

    Last two times I tried to drive on snow, I fell...

    Last two times I tried to drive on snow, I fell over. Very embarrassing. No real damage though. So if there's a chance of ice
    on the road, or rain that might linger on as black ice, I four...
  11. Replies
    153
    Views
    11,817

    Napoleon bar-end mirrors. Use those. They...

    Napoleon bar-end mirrors. Use those. They provide a decent view of something other than your elbow.

    Hot-Hands heater packs. Buy em in bulk from someplace like home depot. They're iron...
  12. "Which is kinda strange, because the motor and DC...

    "Which is kinda strange, because the motor and DC Drive makers specify 230 VAC in for 180 VDC out or 120 VAC in for 90 VDC out."

    Hardinge made all kinds of feed motor electrics. Some of the...
  13. +1 on the LPS3. Don't buy the spray cans. Buy a...

    +1 on the LPS3. Don't buy the spray cans. Buy a gallon of liquid and a brush.

    Good advice on the "sell now, buy later" idea. However if any spouse gets left behind for
    an upgrade, that's...
  14. Or, NOT do anything they *don't* want to. Read...

    Or, NOT do anything they *don't* want to. Read the USSC decison....
  15. How about suing gun makers to stop gun violence? ...

    How about suing gun makers to stop gun violence? Oh, that pesky "can't sue gun manufacturers
    law." right?

    Oooops:

    Docket for 19-168
  16. "- if I go over 50%, bad things happen: -- the...

    "- if I go over 50%, bad things happen:
    -- the variac is starting to get hot (starts smoking)"

    Check to see you did not accidentally interchange variac terminals during the rewire.
  17. Replies
    9
    Views
    1,039

    [QUOTE=rpseguin;3441487]Dealer? Nope, a local...

    [QUOTE=rpseguin;3441487]Dealer?

    Nope, a local hobbiest. He did me a favor one time, long story.
  18. I always keep a couple of brass 5Cs around for...

    I always keep a couple of brass 5Cs around for just such kinds of jobs.
  19. Replies
    28
    Views
    1,817

    [QUOTE=thermite;3441210]Domesticated Cats kill...

    [QUOTE=thermite;3441210]Domesticated Cats kill because they are still cats. No longer much to do with food.

    Domestic cats kill rodents because the rodents are in the cats' territory. The...
  20. Yep, unity gain follower as an input buffer on...

    Yep, unity gain follower as an input buffer on each channel. You just tie the output of the
    op-amp to the negative input.
  21. Replies
    78
    Views
    6,418

    Nope, not all of the site. Mostly just you.... ...

    Nope, not all of the site. Mostly just you....
    Hammer always hits the tallest nail the most.
  22. Replies
    268
    Views
    16,577

    [QUOTE=thermite;3441066] Meanwhile, back in...

    [QUOTE=thermite;3441066]
    Meanwhile, back in Virgin-inyah, a new round of Dumbasscraps ...

    Ah. DDS. Democrat derangement syndrome!

    Guess your fellow virginians got tired of being 'educated'...
  23. Replies
    78
    Views
    6,418

    Nothing ever happens by mistake or without the...

    Nothing ever happens by mistake or without the (at least tacit) approval of management in any organization. This is
    something I've learned the hard way over the years. If it looks bad and stinks,...
  24. Yeah. Like Merrick Garland. In reverse.

    Yeah. Like Merrick Garland. In reverse.
  25. Replies
    9
    Views
    1,039

    I've seen the Aciera, the man is local to me. ...

    I've seen the Aciera, the man is local to me. Nice machine. Not sure why the listings
    here are so cryptic.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4