Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: kctallguy

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    263

    T303 BSQ Round Bar Suppliers

    Looking for recommendations on suppliers for T303 BSQ Round Bar. I have two suppliers I use now but have been getting more orders using BSQ and would like to find more suppliers to get quotes from....
  2. Replies
    11
    Views
    1,848

    Until the customer rejects them for non...

    Until the customer rejects them for non conformance... Covering my baces...

    Sent from my Moto G (5) Plus using Tapatalk
  3. Replies
    11
    Views
    1,848

    Are the dimensions on the prints before heat...

    Are the dimensions on the prints before heat treatment/carberizaton or are they the finished dimensions after heat treatment/carberizaton? Just looking for some clarity as it will affect the final...
  4. Replies
    16
    Views
    2,028

    If it's a single part and you have access to an...

    If it's a single part and you have access to an indexer and a Bridgeport you could broach the hex by hand with a cheap HSS tool bit using the quill and indexing accordingly every 60 degrees......
  5. Replies
    16
    Views
    2,028

    What material are you trying to broach??? ...

    What material are you trying to broach???

    Sent from my Moto G (5) Plus using Tapatalk
  6. Replies
    68
    Views
    5,168

    The company is Newssor Inc. Sent from my Moto...

    The company is Newssor Inc.

    Sent from my Moto G (5) Plus using Tapatalk
  7. Replies
    68
    Views
    5,168

    I had a problem that was similar on an older OM...

    I had a problem that was similar on an older OM control. I found a company on the internet out of Illinois that made a replacement LCD conversion and it was less than $400. I sprung for it and was...
  8. I have 24v at the power supply and checked for...

    I have 24v at the power supply and checked for 24v at the I/O boards as well. It almost seems like the I/O board for these "switches" aren't getting sent to the Fanuc side of things if that makes any...
  9. Sharp SV 2412 Overtravel alarms all axis

    So I'm in a bit of a pickle. I have a 2006 Sharp SV-2412 with a Fanuc Oi- MB controller. I blew an air line going to the spindle for the drawbar so I stopped the machine and proceeded to work on it....
  10. Replies
    25
    Views
    1,910

    This is I was trying to explain. I apologize if...

    This is I was trying to explain. I apologize if what I said was more confusing than helpful.

    Sent from my Moto G (5) Plus using Tapatalk
  11. Replies
    25
    Views
    1,910

    The carbide tip is ahead of center line of the...

    The carbide tip is ahead of center line of the tool. It needs to be ground back so the tip of the carbide intersects the center line of rotation of the tool when it's spinning. A little positive take...
  12. Replies
    44
    Views
    4,317

    They were bought out of a high production machine...

    They were bought out of a high production machine shop that went belly up a few years prior to the owner bought the whole shop for a "bargain" as a lot. There were some good machines in the lot but...
  13. Replies
    44
    Views
    4,317

    What we did when doing this was measure across...

    What we did when doing this was measure across the 1:30 to 6:30 direction and 9:30 to 4:30 directions and used cutter comp for these to bring the bore in on diametrical size and ignored...
  14. Replies
    44
    Views
    4,317

    This is just my 2 pennies. There are a lot of...

    This is just my 2 pennies. There are a lot of great answers/solutions here and the topic has gone a couple different directions since the original post so I did sections I guess...

    I can about...
  15. Do the castings have any markings on them?...

    Do the castings have any markings on them? Foundries often put their mark on them. Could possibly backtrack to find the material spec from the foundry if markings are present.

    Sent from my Moto G...
  16. Replies
    31
    Views
    6,442

    Gustafson makes a good point. You make want to...

    Gustafson makes a good point. You make want to try putting "Looking to relocate to (put places here)" above your address line on your resume. Me personally I have never used a cover letter when...
  17. So is this problem fixed now? Just curious...

    So is this problem fixed now? Just curious mostly.

    Sent from my Moto G (5) Plus using Tapatalk
  18. Don't quote me on this but they didn't used to...

    Don't quote me on this but they didn't used to recommend it as I remember reading it on their website. This was years ago so maybe it's different now. I remember reading that they had problems with...
  19. Tripp Lite Keyspan High-Speed USB to Serial...

    Tripp Lite Keyspan High-Speed USB to Serial Adapter, PC & Mac (USA-19HS)


    We use this in my shop. Works well with DNC4U but it's not capable of drip feeding through the USB. You will have to...
  20. Replies
    1
    Views
    291

    Yasnac LX3 - Z Axis Alarms

    Kia KT-15 Lathe - Yasnac LX3 control

    I'm posting this here as there isn't a machine specific forum for my lathe or its control.

    Went out and fired the machine this morning and immediately had 3...
  21. Replies
    4
    Views
    1,436

    Tried messaging you. Your inbox is full. Sent...

    Tried messaging you. Your inbox is full.

    Sent from my Moto G (5) Plus using Tapatalk
  22. Replies
    8
    Views
    1,187

    Just seen this and yes I probably was butt...

    Just seen this and yes I probably was butt posting. My apologies.

    Sent from my Moto G (5) Plus using Tapatalk
  23. Replies
    7
    Views
    1,523

    Thanks for the input Milacron. I have no...

    Thanks for the input Milacron. I have no documentation with the machine so maybe the 6500lbs is correct. I just went off the Google search.

    Update:
    I will be receiving my new piece of equipment...
  24. Replies
    8
    Views
    1,187

    B Sent from my Moto G (5) Plus using Tapatalk

    B

    Sent from my Moto G (5) Plus using Tapatalk
  25. Replies
    8
    Views
    1,187

    Llb Sent from my Moto G (5) Plus using Tapatalk

    Llb

    Sent from my Moto G (5) Plus using Tapatalk
Results 1 to 25 of 47
Page 1 of 2 1 2