Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JohnEvans

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds; generated 29 minute(s) ago.

  1. Replies
    8
    Views
    424

    Well I have a Boyar-Schultz 618-2A with coolant...

    Well I have a Boyar-Schultz 618-2A with coolant and it does not make a mess unless you pour coolant on like a fire hose ,no real shielding . I just put it on Craigslist Phoenix the other day if you...
  2. If you buy a 3 jaw chuck get one with the...

    If you buy a 3 jaw chuck get one with the removable top jaws. As far as that goes you can always hold a smaller 3 jaw in the 4 jaw.
  3. Replies
    3
    Views
    644

    Looks like the typical Chinese/Taiwan belt head...

    Looks like the typical Chinese/Taiwan belt head 12X36 sold by Jet -Grizzly -corner candy store etc. Does have a Trav-a-dial nice. Parts good luck may find some from Grizzly that will work but don't...
  4. Any go buy a lottery ticket while your luck holds...

    Any go buy a lottery ticket while your luck holds !! I am beyond amazed that MSC had any parts for that lathe ! My experience with any old ENCO machines I usually ended up adapting/fitting a similar...
  5. Yep ! The OP better take Moonlight's offer as...

    Yep ! The OP better take Moonlight's offer as when I sold similar lots I sold for $75-80.
  6. Replies
    12
    Views
    1,120

    Chrome ways on the knee =good. Table ,take a dull...

    Chrome ways on the knee =good. Table ,take a dull old smooth cut or similar and draw file to get the high spots/burrs knocked down and finish with a stone. Then leave it alone,small dings don't hurt...
  7. Replies
    7
    Views
    583

    It is a "crotch"center normally use for drilling...

    It is a "crotch"center normally use for drilling a hole in the side of a round item with a drill bit held in the headstock.
  8. Replies
    2
    Views
    853

    Sorry already sold,forgot to mark this add as...

    Sorry already sold,forgot to mark this add as sold.
  9. FS Mitutoyo Universal Bevel Protractor Set

    SOLD ! SOLD Excess to my needs $115 shipped. Box shows some shelf wear protractor looks as new. Paypal and please show your interest on this thread.
  10. google is your friend ! Try High Quality Tools .

    google is your friend ! Try High Quality Tools .
  11. Replies
    15
    Views
    720

    You DID clean and lube the jaws/screws ? Second...

    You DID clean and lube the jaws/screws ? Second call up the seller of the lathe and talk to them. Even the best quality machines will sometimes get outside vendor supplied parts that have issues.
  12. Try Hastings they use to very good about...

    Try Hastings they use to very good about supplying odds.
  13. Replies
    11
    Views
    1,243

    Not familiar with a 508 pictures ? 608 were the...

    Not familiar with a 508 pictures ? 608 were the ones I have been around. Canada made last made '86 or so. What taper ? R-8 or? Also pictures of tooling. Off the top of my head your area $1000-4000...
  14. Yep, MEEHANITE !

    Yep, MEEHANITE !
  15. Replies
    1
    Views
    298

    I'm assuming that system is the same as a BP ,and...

    I'm assuming that system is the same as a BP ,and normally you can not engage the feed with the quill fully in the up position. That area in the few Sharp's I've ran looked same same as a BP. On a BP...
  16. Replies
    5
    Views
    3,310

    9 year old post and the OP is BANNED ! Not likely...

    9 year old post and the OP is BANNED ! Not likely to get a reply !
  17. FYI Bridgeport made 2 sizes of boring head #1 and...

    FYI Bridgeport made 2 sizes of boring head #1 and the #2 . The #1 uses 3/8 shank bars. I prefer my BP 2 to the Criterion I also have ,why 3 boring heads ?? Got Me !!! LOL
  18. And don't over pack the bearing,about 2/3 full is...

    And don't over pack the bearing,about 2/3 full is plenty.
  19. Well I don't see any change gears and without...

    Well I don't see any change gears and without them you will not be cutting threads ,plus to do metric you will need transposing gear[s]. If you are missing those gears and only the one chuck and if...
  20. Replies
    2
    Views
    429

    What do you want to do,turn between centers? If...

    What do you want to do,turn between centers? If so make a shouldered piece that the shoulder goes against the chuck jaws ,then turn a 60* taper on the end that is sticking out of the chuck. Lathe dog...
  21. Replies
    8
    Views
    938

    Well finding used is probably a very slim chance,...

    Well finding used is probably a very slim chance, so time to either make or modify a standard available gear. Needed 2 gears for my Chinese 18" lathe ,ordered cutters of eBay from China cheap. Made...
  22. If it is a simple small section flat belt as used...

    If it is a simple small section flat belt as used on my non-vary speed Hamilton McMaster-Carr can provide. They have them made to order/length with about a 2 week lead time. Reasonable pricing ,had a...
  23. Replies
    5
    Views
    485

    As I have said before when dealing with way out...

    As I have said before when dealing with way out of production machine tools ,if you can EVEN get the parts pay up and be happy.
  24. Replies
    16
    Views
    1,384

    Buy something you can get parts for ! Total...

    Buy something you can get parts for ! Total orphan veri-speed ,odd collet system, not under power PASS !!
  25. Steve: The part furthers to the right in the...

    Steve: The part furthers to the right in the picture looks like the back half of the wheel mounting hub,the small thread at the end looks like it is left hand . And the wheel flange nut thread also...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4