Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JohnEvans

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    727

    No visible marks/damage on the point and rotates...

    No visible marks/damage on the point and rotates smoothly .
  2. Replies
    3
    Views
    727

    F/S Albrecht -Concentric center-Tomico

    Got 2 chucks one one 5/8 straight shank smooth decent jaws $85
    Second one on Kwic Switch 200 shank smooth jaws look new new $140
    SOLD pending payment Concentric spring loaded live center #2 Morse ...
  3. Replies
    4
    Views
    736

    Special assembly tooling/fixtures ?

    Special assembly tooling/fixtures ?
  4. Replies
    2
    Views
    309

    Go to Lathes + Machine Tool Archive...

    Go to
    Lathes + Machine Tool Archive
    Has a write up on those. Did not see a manual on his listings. I would say a pretty decent machine . Never heard of a "Sofia".
  5. Replies
    2
    Views
    439

    Take a look here "Ford" Llathe...

    Take a look here
    "Ford" Llathe
  6. Thread: Wanted

    by JohnEvans
    Replies
    2
    Views
    453

    Yep dumb title award for the week here. Ebay is a...

    Yep dumb title award for the week here. Ebay is a likely your best bet. If you have plenty of $$ Logan still supplies parts. Good chance the the thread dial assy. was the same for the 11" and maybe...
  7. Well that is what my 1986 BP operators & parts...

    Well that is what my 1986 BP operators & parts book states, 2 different part# for left and right! So who knows??
  8. NOPE !! Parts list show different numbers. Left...

    NOPE !! Parts list show different numbers. Left side takes 2 bearings RH only 1 Bearing seat is wider on LH.
  9. The 2 Webb mills depending on condition and...

    The 2 Webb mills depending on condition and tooling included here in Phoenix $4000-6000 each. The Goodway lathe again depending on chucks toolpost and any tooling about the same. The CNC stuff not a...
  10. Replies
    13
    Views
    1,181

    Duhh I think so !! rub equals friction that...

    Duhh I think so !! rub equals friction that equals HEAT !! You may also have a electrical issue but to start fix the rub.
  11. As said earlier the cylinder also serves as the...

    As said earlier the cylinder also serves as the reservoir/tank. That fitting very well maybe a breather besides being the filler port, being it is on the non-pressure side of the cylinder.
  12. Replies
    62
    Views
    5,721

    Google to the rescue Creeper Caster 3 in Use...

    Google to the rescue
    Creeper Caster 3 in Use With 4WM23 PK4
  13. Replies
    62
    Views
    5,721

    I prefer the old style creeper wheels ,the ones...

    I prefer the old style creeper wheels ,the ones that roll on the edge, casters like most modern creepers have suck. I had a gennie Lisle "jeepers creeper" for damm near 50 years till I backed over it...
  14. Replies
    13
    Views
    1,245

    Torch one out from a piece of 1/4-3/8 strap ,a...

    Torch one out from a piece of 1/4-3/8 strap ,a bit of finish work with a 4-1/2 grinder and Bob's your uncle !!
  15. Replies
    9
    Views
    508

    do those oil fill cups have some felt inserts to...

    do those oil fill cups have some felt inserts to meter the oil? If not unless you oil them every few minutes those bearings will be running dry more often than not. That would be a good place for a...
  16. Replies
    6
    Views
    799

    Wood lathe or possibly a metal spinning lathe....

    Wood lathe or possibly a metal spinning lathe. Weird TS who knows?? I'm sure there was some reason for it though.
  17. Replies
    3
    Views
    744

    Machining books

    Set of 8 "Modern Shop Practice" in 4 othersvery good condition plus 4 others [see pictures for titles]
    $80 shipped priority FR Absored all I could out of these so time to pass on to the next reader!...
  18. Replies
    25
    Views
    1,443

    And that's why you DO NOT extend the slide out...

    And that's why you DO NOT extend the slide out beyond the end of the base for general use! But fixable for sure.
  19. Replies
    35
    Views
    8,291

    Well nowadays I don't know how big a OS pistons...

    Well nowadays I don't know how big a OS pistons for that would be available. Back in 70s and earlier I would expected to find .080s from someone like Badger-Silvolite etc. Those flathead Continentals...
  20. Replies
    29
    Views
    2,245

    Well the big question is where this part was made...

    Well the big question is where this part was made ??? If in the USA and more than 20-30 years ago inch thread 99.44% sure. If from over seas metric same % chance. Do not often see metric threads in...
  21. Replies
    35
    Views
    8,291

    Well if you COULD get a reply with the block...

    Well if you COULD get a reply with the block casting # which would be F600AXXX that would tell you that it was the right 6 cyl series. What is the bore on your old engine you know? Your old engine...
  22. Replies
    35
    Views
    8,291

    You do know that the F209-F226 series engines are...

    You do know that the F209-F226 series engines are the same size outside dimension wise ? The usual biggest difference between forklift engines and the rest is most forklift engines have 5 gear front...
  23. Being that is a duel voltage motor it IS wired...

    Being that is a duel voltage motor it IS wired for the voltage you are using? I would think a 1/2 HP capacitor start and run motor would be the correct one for that lathe. As I said earlier SB's flat...
  24. The question IS what motor is on there now ?...

    The question IS what motor is on there now ? Would be very unlikely your current motor has either brushes or magnets. 1hp motor is a bit big as SB's are limited by the flat belt for power...
  25. Gee ,Looks more like a planer to me !!

    Gee ,Looks more like a planer to me !!
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4