Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cole2534

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. A case is 10 boxes, I bought half of their...

    A case is 10 boxes, I bought half of their prescribed limit. That's just enough to take the wife out for a round of sporting clays with a small warm-up and some spares.
  2. Yessir! I'm of the opinion that if you're...

    Yessir!

    I'm of the opinion that if you're capable of properly storing, maintaining and operating it, no weapon should be off limits. Properly being the key word. If you want to throw some hand...
  3. I have 7 of the same gun. I really like Sig...

    I have 7 of the same gun. I really like Sig P320's.....

    But if I had to do it all over again, I'd own fewer guns and spend more on mags/ammo/gear and TRAINING.

    And night vision. NOD's are...
  4. Please tell the media this. Every damn time they...

    Please tell the media this. Every damn time they arrest some retard with a gun collection it's an 'aresenal'. In reality, it less gear and ammo than I take home from a match.
  5. Replies
    35
    Views
    1,810

    I once rented a shop that had tie points in the...

    I once rented a shop that had tie points in the floor, think they were for vehicle frame alignment work maybe. They turned out to be handy as hell.

    Programmed via Mazatrol
  6. Replies
    19
    Views
    1,545

    I'm interested in this as well. Programmed via...

    I'm interested in this as well.

    Programmed via Mazatrol
  7. I have three drawings on my desk just like that. ...

    I have three drawings on my desk just like that. A small family of parts with an angular callout that can't be achieved without violating other tols.

    Programmed via Mazatrol
  8. I happened into 3, NOS Bison lathe chucks. ...

    I happened into 3, NOS Bison lathe chucks. D1-8, 10". Thru hole is a tickle over 3" per my snap gage. 1pc jaws is the only kicker.

    They have some staining, but the cross hatch is still...
  9. Replies
    1
    Views
    392

    T32 control - limiting wasted motion

    Whats the trick to getting a tighter retract or safe plane on a T32? Program has 3 tools (profile, parting, puller) and seems to travel way too far in Z+ to make the changes, as in multiple inches...
  10. Well, she gone. Now I need another Monarch,...

    Well, she gone. Now I need another Monarch, 16x54-ish.
  11. Me too! ...

    Me too!

    https://uploads.tapatalk-cdn.com/20211010/bd837dd8f93ad1889ddb096a1d9589fb.jpg

    Programmed via Mazatrol
  12. Considering I've NEVER seen you post anything...

    Considering I've NEVER seen you post anything you've actually made, I bet your drill sharpening time is quite limited.
  13. I ran into a similar situation, but it worked in...

    I ran into a similar situation, but it worked in my favor. Cabelas had a 5 box limit, except shotgun shells, those went by the case. So I bought 25 boxes of shotgun shells. :)

    Programmed via...
  14. Once I figured out the right tools, I don't think...

    Once I figured out the right tools, I don't think Ive put an endmill over 1/2" in my 2J since 2013 but once. Maaaaybe twice.

    Programmed via Mazatrol
  15. I always thought a Sterling dril grinder would be...

    I always thought a Sterling dril grinder would be excellent for a job shop.

    Programmed via Mazatrol
  16. Ill take 3, pm coming.

    Ill take 3, pm coming.
  17. Replies
    19
    Views
    1,009

    That's my predicament. I did find that Amazon...

    That's my predicament. I did find that Amazon has good pricing on full boxes of Unbrako's. But they're a last resort.

    Programmed via Mazatrol
  18. You'll run out of machine stiffness before HP, in...

    You'll run out of machine stiffness before HP, in my experience. If I was dead set on a facemill, I'd go with a 2" or maybe a 2.5".

    Like so- 2 INCH ZCC FMA11

    Programmed via Mazatrol
  19. Replies
    19
    Views
    1,009

    Usually a dozen at most, but I prefer to buy a...

    Usually a dozen at most, but I prefer to buy a box of 100 or 50 or whatever.

    Programmed via Mazatrol
  20. I should like to have that. Any guesses on...

    I should like to have that. Any guesses on freight okc, ok?
  21. Never bought a reground tap, but I am looking for...

    Never bought a reground tap, but I am looking for this size. Surely the only touch up the face and not the OD?

    Programmed via Mazatrol
  22. Replies
    15
    Views
    1,058

    Which 1.5" bushings are left? Price with...

    Which 1.5" bushings are left? Price with shipping to OKC, OK?

    Programmed via Mazatrol
  23. Replies
    4
    Views
    510

    Trim 690xt Programmed via Mazatrol

    Trim 690xt

    Programmed via Mazatrol
  24. Replies
    19
    Views
    1,009

    Online fastener source

    Who does you folks prefer for buying bolts or screws online?

    I occasionally get into a project and need some screws, in this case M8 x 25mm. I want to buy a box of Holokrome or equivalent but...
  25. I paid $70/bx for Winchester 200rd 115gr at...

    I paid $70/bx for Winchester 200rd 115gr at Academy last week. 4 box limit gets you 800rds. :)

    Programmed via Mazatrol
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4