Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Hoss710

Search: Search took 0.00 seconds.

  1. just noticed a dark spot around the R3 markings....

    just noticed a dark spot around the R3 markings. might want to give that a closer look to. all the current for tool changer in and out. as well as turret rotation go through the 2 groups of the...
  2. the double resistors from factory are total...

    the double resistors from factory are total normal. I'd re soldier the single resistor as the joints look cold or have had heat in them thru the resistor.


    when you go to diagnostics , look for...
  3. for some reason my last post disappeared when I...

    for some reason my last post disappeared when I went to make a correction from spell check. I'll re post it in a bit
  4. also the top of that same resistor ( single 1)...

    also the top of that same resistor ( single 1) looks like it's been hot as well. I'd reflow both solider joints.
  5. tip of the day for ya.if your looking for a easy...

    tip of the day for ya.if your looking for a easy way to send the toolchanger back home . under the jog button is zero return. push zero return. then go to the letter key pad bottom center and...
  6. go to diagnostics screen to discretion inputs ....

    go to diagnostics screen to discretion inputs . if you look down thru the list you tool change in . tool change out. that's how you can test the switches. the resistors are on the IO board top right...
  7. 1st check for a stuck switches if the home switch...

    1st check for a stuck switches if the home switch sticks it will fault out without going very far. 9 times out of 10 it's a stuck home switch. the tenth time it's a bad relay or resistor on the IO...
  8. actually try disabling switch on the fly first....

    actually try disabling switch on the fly first. and see if the spindle stops then switches. then turns back on.
  9. yes that is them . yes I would try disabling both.

    yes that is them . yes I would try disabling both.
  10. no I would leave everything connected. go into...

    no I would leave everything connected. go into the parameters I believe it's in 57 or 209 ( it's in the first 3 pages, parameters start at 57). there is 1 that says delta/ wye . it should read 1....
  11. the delta /wye was a design around giving the...

    the delta /wye was a design around giving the machine more bottom end torque without the cost of a gearbox. when everything is happy it actually works pretty good. there is some ramp up parameters...
  12. oh 1 other thing I didn't mention with my phase...

    oh 1 other thing I didn't mention with my phase converters ( I have 4 all together. 2 that can run in parallel, 2 just for their dedicated machines) is I run 00 double ought wire to them all. and 4...
  13. you have 2 variables here in play that...

    you have 2 variables here in play that unfortunately unless you have near a identical machine as what others are talking about, it's not the same. you have both a early vector drive, and delta /...
  14. Aldo just noticed you are running a phase...

    Aldo just noticed you are running a phase converter ( I have been running them for 20 years at my shop) what size motor are you running? and is it the only machine being powered by it? to run my vf3...
  15. ok 2 things stand out at me from your...

    ok 2 things stand out at me from your description.
    1 high leg should be on middle of your 3 incoming legs.
    2 are your taps set to your high leg? if so you will have to drop 1 or 2 voltages on...
  16. push the contactor in as hard as you can . in the...

    push the contactor in as hard as you can . in the meters lowest setting it should read basically 0 ohms. another thing to consider is both the breaker size you used, and what gauge wire and how far...
  17. was there something wrong with the reply I left...

    was there something wrong with the reply I left you on the same machine on your other post ?
Results 1 to 17 of 18