Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: animal12

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    143
    Views
    161,047

    Tex , welcome back , you had mentioned earlier in...

    Tex , welcome back , you had mentioned earlier in this post that you would be willing to share your code for engraving the new large dials . Wondering if your offer is still available ?
    thanks...
  2. Replies
    1
    Views
    922

    any pictures ? model #'s ? animal

    any pictures ? model #'s ?
    animal
  3. What are you asking for the 6 jaw & the Digimatic...

    What are you asking for the 6 jaw & the Digimatic & the height gage & what's the height gage mdl #
    thanks
    animal
  4. what's the tool holder with all the set screws...

    what's the tool holder with all the set screws above the tool post in pic # 2
    thanks
    animal
  5. Replies
    5
    Views
    605

    make sure that the bearings & spindle are wet /...

    make sure that the bearings & spindle are wet / coated iwith spindle oil before you do the lift test
    animal
  6. Replies
    21
    Views
    2,355

    Are you using the half nuts , or the power feed ?...

    Are you using the half nuts , or the power feed ?
    animal
  7. Replies
    30
    Views
    2,579

    where in CA is it ? animal

    where in CA is it ?
    animal
  8. here you go DRO for the Compound Angle | The...

    here you go
    DRO for the Compound Angle | The Hobby-Machinist
    animal
  9. I'm not saying that this is true all the time ,...

    I'm not saying that this is true all the time , but sometimes you need to look at it like this .
    1 How much does the part cost to buy ?
    2 how expreienced al I
    3 is this a project that can cause...
  10. Replies
    20
    Views
    1,190

    I've seen a few tool holder's like shown in the...

    I've seen a few tool holder's like shown in the tailstock in the pictures . Is there a particular name for those . Do they have any kind of accuracy ?
    tks
    animal
  11. Another thing to keep in mind as your quest goes...

    Another thing to keep in mind as your quest goes on is that if you keep the brand originally mentioned at the top of this post on your list of options , they made alot of parts out of Zamak . Zamak...
  12. Replies
    11
    Views
    960

    Good deal , tahnks James , let me know , no hurry...

    Good deal , tahnks James , let me know , no hurry
    animal
  13. Replies
    11
    Views
    960

    What do you want for it ? I could be interested...

    What do you want for it ? I could be interested in it if Canada falls through . Fit in a flat rate box ?
    thanks
    animal
  14. Replies
    15
    Views
    927

    Cool , thanks for that ! Saved & printed & on the...

    Cool , thanks for that ! Saved & printed & on the stack for the next time I get out to the shop .
    animal
  15. Replies
    15
    Views
    927

    Thank you folks for all the insight . I got a bit...

    Thank you folks for all the insight . I got a bit of time to get out in the shop today & it appears that all is well in the universe !!
    Question , if I am threading but using a crank in the spindle...
  16. do you know how a water level works ? I think...

    do you know how a water level works ? I think that may be part of the problem .I would order a set of spindle wicks & put the original Gits
    oilers back in . Ans don't forger to soak the new wicks...
  17. Replies
    15
    Views
    927

    I think I have made a MAJOR ROOKIE MISTAKE , I've...

    I think I have made a MAJOR ROOKIE MISTAKE , I've veen using the clutch instead of the half nuts . Will retry & report back tomorrow .
    thanks
    animal
  18. Replies
    15
    Views
    927

    OK it looks like I'm getting 32 tpi & I'm trying...

    OK it looks like I'm getting 32 tpi & I'm trying to get 16 , so I'guessing I have one of the non internal gear box gears off . MY Army manual does not have all the gears numbered that way . No 37 in...
  19. Replies
    15
    Views
    927

    I'll got back to the shop tomorrow & see . I was...

    I'll got back to the shop tomorrow & see . I was trying for a 16 tpi & the results came out much finer .
    thanks
    animal
  20. My 2 cents here , which may be only worth 2 cents...

    My 2 cents here , which may be only worth 2 cents . I realize your kinda tight on space but that lathe only has 10"- 12" between centers
    depending on where you find specs . Thats a pretty limited...
  21. Replies
    15
    Views
    927

    9A QCB threads are wrong (my fault )

    I just tried to do my first threading with my lathe . It's a 40 something 9A . I did the rebuild following directions in the Ilion book but somewhere I messed something up & my threads don't match...
  22. Replies
    35
    Views
    3,380

    So how are you mounting the boring head to the...

    So how are you mounting the boring head to the block ? I'm guessing that teh boring head has a taper of some sort ? MT , R8 , or something like that ?
    thanks
    animal
  23. Thread: Bearing Grade

    by animal12
    Replies
    17
    Views
    1,564

    thank's for those pic's . A update here . The...

    thank's for those pic's . A update here . The spindle diameter whre teh thrust bearing & washers go is 30.1 mm & the bore for them is 44.40 mm . So it looke like I have room to go to a 44 mm bearing...
  24. Thread: Bearing Grade

    by animal12
    Replies
    17
    Views
    1,564

    thanks folks . I'll try to get out to th eshop...

    thanks folks . I'll try to get out to th eshop this afternoon when I get back in & measure the spindle & the housing for the thrust bearing.
    thanks
    animal
  25. Thread: Bearing Grade

    by animal12
    Replies
    17
    Views
    1,564

    OK here's a few pice with dimensions . The 2...

    OK here's a few pice with dimensions . The 2 thrust washeers have slightly different thickness & the 1 on the right in the pic is not completelyflat by a @ .0010 - .0020 . The bearing race itself...
Results 1 to 25 of 168
Page 1 of 7 1 2 3 4