Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: dinotom

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    63
    Views
    15,970

    Dave, Ill take those round dials, I also still...

    Dave,

    Ill take those round dials, I also still want the gear box if you will ship it
  2. Replies
    7
    Views
    533

    Thanks, I left it alone since it seemed fine and...

    Thanks, I left it alone since it seemed fine and replaced everything else. I didn’t have the right size bearing separator and couldn’t wait for it to come. It’s all reassembled and back in the...
  3. Cal, Here is the machine tag 288118 I...

    Cal,

    Here is the machine tag

    288118

    I used the Dymo Rhino 4200 label maker as shown in Thermite's link.

    Re: the white wires...yes, I remembered that but couldn't find where the posts...
  4. Re-wired the whole machine

    I had to replace some wires that were damaged and decided to replace all the wiring and redo the conduits, eliminating the annoying metal tubing Monarch used and replacing that with flexible gray...
  5. Replies
    18
    Views
    1,639

    Cal, Thanks. I was going to make a tool to...

    Cal,

    Thanks. I was going to make a tool to pull it but you're right, a bearing separator would work. I will try it tomorrow. I spent today finishing up the re-wiring and re-conduiting (using flex...
  6. Replies
    7
    Views
    533

    While you are hot, any idea how this bottom...

    While you are hot, any idea how this bottom bearing comes off because the shaft does not press out of the gear. I have the top bearing off, its just sitting on the shaft.

    Bearing that needs to...
  7. Replies
    7
    Views
    533

    Brilliant ! That was the answer, thank you very...

    Brilliant !
    That was the answer, thank you very much


    Sent from my iPhone using Tapatalk
  8. Replies
    7
    Views
    533

    They shaft won’t come out unless the two screws...

    They shaft won’t come out unless the two screws that go thru the shaft and had the jam nuts on the end come out first. Can’t see how that’s possible with the heads on the backside


    Sent from my...
  9. Replies
    7
    Views
    533

    Back Gear dis-assembly procedure

    I am posting this outside my restoration thread so that answers will be readily found by others who may wish to find the same information.

    Back Gear Box
    287868

    I have dis-assembled the back...
  10. Replies
    18
    Views
    1,639

    Carl, Here is the image of the gearbox as it is...

    Carl,
    Here is the image of the gearbox as it is now.

    287830

    that small shaft on the end you noted in the parts diagram will not come off, therefore I cannot get the gearbox out of the machine.
  11. Replies
    18
    Views
    1,639

    Yes, I got the end cap off fine. It was sealed...

    Yes, I got the end cap off fine. It was sealed tho. I’ll re-look at the shaft this morning.

    Note: Looked at the parts picture and I see what your describing in Part #24.
    I tried again to pull...
  12. Replies
    18
    Views
    1,639

    Please see the post that I put up probably just...

    Please see the post that I put up probably just prior to your post. Post #8
  13. Replies
    18
    Views
    1,639

    Well I went to remove the tumbler shaft and it...

    Well I went to remove the tumbler shaft and it wouldn't come out. I tried every combination of gear and screw settings but it won't come out (yes, I started with what was said in #7 first). I thought...
  14. Tachometer gear

    I want to dis-assemble the tachometer to replace the needle which is bent/partially broken. There is a gear on the back of the tachometer shaft.

    287294

    As I went to take this gear off, I really...
  15. I would love some pictures of the underside of...

    I would love some pictures of the underside of the lever, showing the mechanism.

    No rush required, I am at least a week away from putting that back together and back on the machine.

    Thank you...
  16. Thermite, Please explain to me how a snap ring...

    Thermite,

    Please explain to me how a snap ring in a groove in the interior of a housing that has no ears with holes and needs to expand outwards can be removed. And yes, sarcasm noted, but I’ve...
  17. Dave, Once the shaft is out, yes I'm guessing...

    Dave,

    Once the shaft is out, yes I'm guessing the bearing will press out the other way BUT if I can't get the key out of the shaft end where this bearing is, this snap ring cannot be removed as...
  18. I found a feedstock gear on Ebay and it looked...

    I found a feedstock gear on Ebay and it looked far better than mine so for $40 I bought it. I also ordered the gaskets from Monarch, two week lead time. Since I now have two weeks before I can...
  19. Replies
    9
    Views
    1,807

    Yes, I am going the gasket route as I am not...

    Yes, I am going the gasket route as I am not particularly good with Permatex. I ordered what was readily available from Monarch and will make the others as I have plenty of gasket material around,...
  20. Replies
    9
    Views
    1,807

    Thank you. Yes, I have a round dial 1944...

    Thank you.

    Yes, I have a round dial 1944 vintage. Isn't it better to just use Permatex and make your own gasket like seals on the parts?

    I emailed Terrie and she sent me a list of all the...
  21. Replies
    9
    Views
    1,807

    Where/how did you get the parts numbers for all...

    Where/how did you get the parts numbers for all those gaskets? I recognize the shape of 4 of those coming from parts on parts diagram E1-B of my manual, but the parts listing for diagram E1-B makes...
  22. Replies
    7
    Views
    609

    Thermite, Because I like to ensure when the...

    Thermite,

    Because I like to ensure when the non-identical replacement parts come they measure out and look correct before I actually use them.
  23. Replies
    7
    Views
    609

    Well, I searched on google for foot punch and...

    Well, I searched on google for foot punch and foot punch tool, and still have no idea what that is and trust me, I have most every tool known to man.

    Can you post a picture and link to where I can...
  24. Feed gear in housing

    Although the other side of this gear looks perfect, the rear facing side looks oblong to me. But this gear is keyed, so should I assume this isn't that big of a deal? I can remove and fix later if...
  25. Here it is. I have it. I took it out when I...

    Here it is. I have it. I took it out when I removed the apron and shafts.

    Part E-12
    286654
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4