Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: browniesharp

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    1,288

    My T&G did not come with a taper...

    My T&G did not come with a taper attachment;however, I was able to acquire a partial taper attachment from board member shapaholic. I believe 5 pieces were missing. One of which was the sliding...
  2. If you want to possibly save some money and have...

    If you want to possibly save some money and have the time & skill, there are a couple of people over on the [email protected] that sell castings for various accessories. Jim Switters had or...
  3. I had cataract surgery but only in one eye and...

    I had cataract surgery but only in one eye and made a different focal length selection. Rather than select either a near or far lens, a single focus lens “for computer distance” was chosen. I do...
  4. Replacement bearings for the M head spindle pulley.

    I’m replacing the bearings in the spindle pulley of an M head and am uncertain as to the proper replacement bearing. My internet searching indicates that a pair of 6206 bearings is the usual...
  5. Other Options for Vertical head on a TM

    Clausing and Rockwell/Delta made small vertical mills with quills with around three inches of travel. I believe the Clausing only had a Morse 2 taper while the Rockwell had an R8 spindle. Perhaps...
  6. Drawings from Hendeyman could rescue this machine

    Although some may consider this a “parts” machine, mostly likely it can be restored to full functionally. I don’t know if it is missing the cross slide/compound and the tailstock. I know in my...
  7. Replies
    36
    Views
    2,412

    To get back to the poster’s original quest,...

    To get back to the poster’s original quest, (assuming the lathe in question is B/C Tool & Gagmakers lathe) there is another consideration. Hendeyman has many prints available for this machine and...
  8. Replies
    36
    Views
    2,412

    That does indeed sound like a B/C tool &...

    That does indeed sound like a B/C tool & Gagemaker lathe. These were designed in the late thirties so they are contemporaries of the Monarch 10EE. They were initially 9 X 18 inch machines which...
  9. There is also "Fatigue Proof" which has the same...

    There is also "Fatigue Proof" which has the same composition as 1144 with free machining properties. It has a minimum of 30 C Rockwell hardness or Brinell Hardness minimum of 285. There are several...
  10. Replies
    18
    Views
    2,909

    I have a Barber-Colman (later Hendey) 9 X 24...

    I have a Barber-Colman (later Hendey) 9 X 24 lathe, so I don’t know if this applies to your 9 X 18 machine with mechanical drive. I looked at the belts on mine. The three belts between the...
  11. Looking at some K. O. Lee literature for the...

    Looking at some K. O. Lee literature for the SS714 model (6X12) noted as net at 1220 lbs and shipping at 1370 lbs
  12. Replies
    69
    Views
    10,119

    To get back on message: if the Monarch 10ee is...

    To get back on message: if the Monarch 10ee is mentioned, I would also propose the Hendey Tool & Gage Maker. It is slightly smaller - being just a 9 X 24 machine and weighing in around 2500 lbs. ...
  13. I am considering making a 5c collet setup for my...

    I am considering making a 5c collet setup for my T&G. There are a number of articles on such construction projects in the "Home Shop Machinist" magazine (is it permissible to mention this magazine...
  14. Niwot, As I mentioned in my post #5, this is...

    Niwot,
    As I mentioned in my post #5, this is the electronic drive "tube drive" similar to the WIAD drive for the Monarch 10ee. After I purchased the VFD and 3 phase motor, I examined the...
  15. looking at sales literature for this...

    looking at sales literature for this Barber-Colman (Hendey) lathe: speed ranges from 15 to 3000 rpm
  16. Niwot, My T&G (AHL-40041)is sibling of your...

    Niwot,
    My T&G (AHL-40041)is sibling of your machine - made in a batch of eleven AHL-40036 to AHL-40047. Mine was ordered 23 August 1956 and delivered 18 Dec 1956. When I received the...
  17. Replies
    115
    Views
    26,281

    I wouldn’t be discouraged by that .003 bed wear. ...

    I wouldn’t be discouraged by that .003 bed wear. My Hendey T&G was acquired at a tag sale held in a local tool and die shop which was closing down. Many people at the sale felt the “ridge” on...
  18. Replies
    11
    Views
    2,365

    There was a Sheldon group on yahoo but it has now...

    There was a Sheldon group on yahoo but it has now moved to another hosting system something like IO. If you can find that group, there is a fellow - John Knox who worked at Sheldon for many years...
  19. Replies
    19
    Views
    4,312

    I may have exactly what you are seeking. Back in...

    I may have exactly what you are seeking. Back in the early 70's I purchased a 5 inch Perfecto (made in England) hand powered shaper. At that time I believe it was delivered by truck but is not...
  20. Replies
    11
    Views
    1,691

    Josh, I acquired a T&G with the electronic...

    Josh,
    I acquired a T&G with the electronic drive back in 2005. I ordered a schematic for the electronics from Hendyman - DEDA-1-1 and received the identical drawing as shown above (22 by 35...
  21. Two weeks prior to submitting the initial post, I...

    Two weeks prior to submitting the initial post, I contacted Wells Index about a milling machine that would suit my space requirements –36 inch table size and secondly the overall height (low...
  22. Recommendations of rebuilders for a Bridgeport step pulley mill

    I am now looking into having my step pulley Bridgeport mill put back in better condition - “rebuilding or remanufacturing”. This would mean replacing the bearings, grinding/scrapping the table,...
  23. Replies
    1
    Views
    1,051

    Bridgeport M head Dis-assembly

    A while ago I purchased a combination Hardinge TM mill with a Bridgeport M head. I was surprised at the performance of the mill and measured certain performance parameters. Best I could determine...
  24. Replies
    24
    Views
    5,412

    Hendeyman may not have all the information on the...

    Hendeyman may not have all the information on the Hendey line of machine tools but he has an extensive collection on the Tool and Gagemaker lathe. This includes the original purchaser and also how...
  25. Thread: Hendeyman

    by browniesharp
    Replies
    3
    Views
    1,888

    As I recall from phone conversations with...

    As I recall from phone conversations with Hendeyman, He now uses a public computer in the local library and only checks it every week or so.
Results 1 to 25 of 233
Page 1 of 10 1 2 3 4